Models > TGF362BBBA > Instructions

TGF362BBBA Tappan Range - Instructions

All installation instructions for TGF362BBBA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TGF362BBBA
91-105 of 303
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The oven would not light and the house smelled like gas.

  • Customer: Jeffrey from Mission Viejo CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 1 of 2 people found this instruction helpful
I removed the oven floor and subfloor. I detached the old ignighter leaving the wires still attached. I then attached the new ignighter and fed each of the two new wires down through the bottom of the oven floor following the same path of the old wires which were still attached. I attached the new wires one at a time to make sure I connected them to the right place. Then, I pulled out the old igniter. I then attached the oven floors and turned the oven on which now works. The tough part is pulling the oven out from the wall to disconnect the power and turn off the gas. I did not remove the oven door.

I forgot to remove something I had saved in the oven, planning to remove it before using the range.

  • Customer: Marilyn from Clearwater FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

Oven drawer fell out

  • Customer: Donald from Gainesville FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Removed the one remaining drawer guide and stared at it for 10 minutes trying to understand where it came from and how it worked. Looked it up on partselect.com. While there was no part number, the detailed photo on your web site was enought to assure me that you had the correct part. Ordered them in a few moments and three days later I had the parts. The hardest part of the job was trying to understand how to install the widgets. After 20 minutes to crawling around in the stove's inards, I finally got the "aha" and the drawer on this antique stove was finished. Thanks! Couldn't have done it without you.

Oven Igniter failed

  • Customer: MICHAEL from LIVONIA MI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
See other posts.... they have the correct repair procedures.

HIGHLY RECOMMEND removing the bottom drawer to access the space where splice will be made between new igniter wires and existing wires. This step is recommended in previous posts. I wasted a lot of time taking out unnecessary stuff in the oven compartment before I realized that the drawer compartment provided easy access for repair. Story of my life on just about all repairs.

the oven was slow to light and didn't reach the set temperature

  • Customer: James from Chicago IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.

The tubes which fed gas to the burners were broken due to raising and lifting the top cover which caused gas to leak under the top cover.

  • Customer: George from Wheeling WV
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 1 of 2 people found this instruction helpful
I had no experience working on the stove before so it was all new to me. Removed the top cover. Removed the igniters and the burner connections which allowed access to the splash pan. Removed the splash pan and replaced the two broken tubes. Job would have been faster had I known how to access the front burner controls. As a result, we have a fully functioning Tappan range in our kitchen and the range is much better than anything commercially available. They don't make em like that anymore.

Oven wouldn't come on

  • Customer: Arthur L from Huntington IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Unplugged the appl. I removed the bottom of the oven. Disconnected the two wires. Removed two screws that hold the element in place. Replaced it. And put everything back together. Since this element goes bad about every year an a half, I keep one on hand all the time.

Ignition not working

  • Customer: Ricardo from Stamford CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Installed new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.

Oven wouldn't heat , glow from bottom, and strong smell of gas

  • Customer: Clayton from Gulf Breeze FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 1 of 2 people found this instruction helpful
First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two screws on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.

Igniter lights up, but no flame appears, no gas

  • Customer: Denise from Clinton Township MI
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 1 of 3 people found this instruction helpful
I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, worked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,

Oven would not come on, broiler worked and so did the burners

  • Customer: Jackie from Palmdale CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 3 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
And re-connected the same way.
Peice of cake..

Thank You..

The oven wouldn't light or very slow to light

  • Customer: Chris from Shunk PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
Removed the two screws, took out the old one and replaced the new one. It was very easy and the oven works great now. Thanks.

missing drawer glide

  • Customer: Barbara from Cambridge City IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Pulled out the bottom drawer of the stove. Attached the new drawer glide to the drawer. Replaced the drawer and it worked like new!

I received the part two days after I had ordered it. I was very pleased with the speed of the service and the ease with which I found the part I needed on the web site. I will use your site again if needed.

Original rear glides had broken

  • Customer: Jeff from Irvine CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Took the new parts out of the bags, slipped them into place and had the drawer working flawlessly in less than 5 minutes!
I surprised myself.

Gas oven would take forever to light and would not relight if cooking temp was reduced

  • Customer: John from Newmarket NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
1. Unplugged power cord.
2. Removed warming drawer and oven shelves and lower plate
3. Removed old wirenuts from back of warming draw space (awkward to reach in to the back).
4. Removed 2 screws holding ignitor in oven - screws in poor shape and were not reuseable.
5. Found next size up sheetmetal screws and installed new ignitor.
6. Ran wires down adjacent to gas feed into warming drawer space.
7. Connected with wirenuts supplied with ignitor.
8. Replaced everything.
9. Tested oven and ate some tasty blueberry muffins.
All Instructions for the TGF362BBBA
91-105 of 303