Models > TGF362BBBA > Instructions

TGF362BBBA Tappan Range - Instructions

All installation instructions for TGF362BBBA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TGF362BBBA
196-210 of 305
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replace the oven igniter

  • Customer: Mike from Hamburg, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Remove the oven drip pan & burner baffle. unscrew & cut leads to remove old igniter. Splice old leads to new using furnished wire nuts and remount. Job would have been easier with oven door removed, but didnt want to create a new project.

oven would not light

  • Customer: wayne from Washington, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
took off bottom pan in oven and replaced ignitor

oven ignited, but didnt get very hot

  • Customer: ricky from paducah, KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
disconnected the (2) wires of old igniter from (2) wire nuts located under oven in back of bottom drawer, took out (2) mounting screws holding igniter assembly and held it together to new igniter assembly. Stretched out wires together and cut new wires same length as old wires, then mounted new igniter with same (2) screws and connected wires with new included wire nuts and replaced all other oven parts, turned on oven and had a nice TV dinner! :-) Extremely pleased with PartSelect. Ordered part on Tuesday night and had it by Thursday night the week of Christmas no less! Kudos to PartSelect! Great service!

Igniter fail to light the flame

  • Customer: Vic from Vista, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 2 people found this instruction helpful
Removed broiling drawer to gain access to the igniter. Remove igniter from mounting bracket, ,cut wires, attach new igniter wiring and reinstall the igniter on the bracket. Reinstall the broiling drawer to complete the job.

Christmas Day the oven would not ignite. Had to pull out the camper's folding oven for the cheesy potatoes and cook the chicken over an open fire. We Had 10 adults and 5 children (6 and under).

  • Customer: Joseph from Cleveland, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 2 people found this instruction helpful
The day after Christmas I searched the net reading various reviews, etc. PartSelect seemed to be the easiest site to navigate and offered How To's notes. Wednesday, less than two days later the oven igniter arrived. This was the third igniter in six years. The grandkids watched me intensly as I read the How to's and easily installed the new igniter. Because of the ease with the website and the fast delivery I am keeping PartSelect.com as part of my resources for the home self doer. The cost was competitive saving me over $100.00 doing it myself. Thank you PartSelect. Joe W Cleveland, Ohio.

oven stopped working

  • Customer: gerry from dana, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 2 people found this instruction helpful
Removed racks. removed two screws in back of bottom shelf of oven.Do not know what type of nut or other fastener was on other end of those screws as they would not tighten when I put them back in. However they are in the holes and the shelf isnt going anywhere.The shelf lifted right out lifting the back up first and sliding out from under lip in front. easy access to igniter use a nut driver for this.In the bottom left corner there was a triangle shape cover that needed removed held by one screw. both wires had clip in style connectors that come right out.Cut these off with plenty of wire to attach to new wires with wire nuts provided with new igniter.Put everything back like the old came off. I used a little electrical tape over wire nuts.Closed oven door and tuned on oven and watched my wife begin to smile as the igniter turned red and oven kicked on.

Stove would glow but not actually ignite, got worse with time

  • Customer: Scott from Colden, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 2 people found this instruction helpful
took off door, oven floor and burner cover. cut the wire for the old igniter and used ceramic nuts (provided) to hook up the new one. screwed the new one on with old screws, tested and re-assembled. Saved a hundred bucks easily, but I have some basic electrical back ground.

broken drawer slide clips

  • Customer: Richard from Spokane, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Easy peasy! Took all of 2 minutes to replace all four clips. Clips snap in by hand and take a little bit of force to make them seat correctly. These are a frequently-replaced item,so that makes me think they are somewhat fragile. Great prices and quick shipping from PartSelect made this so simple. The local appliance parts dealer wanted $11.00 each for the rear clips! Thanks!

The oven would glow, but not light.

  • Customer: Kristy from Smithfield, UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 2 people found this instruction helpful
First, I took out the racks. Then I removed the bottom cover of the stove. (This was in place by two screws that I used my drill & socket set.) Next, remove burner cover by a socket set. Finally, in the corner was a metal cover that covered part of the electrical connections. I then used the screw driver to undo the screws that attached the igniter to the oven. I undid one wire connection, and wired it with the new one on the igniter. (To make sure I wired it correctly.) Then I undid the other wire, and connected it with the new wire (using the new wiring nuts provided.) Done! Now just put all the parts back together.

broked drawer slide

  • Customer: Thomas from Spring Hill, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
The plastic drawer slide that the lower stove door sits on broke. (one on each side) Remove the old one with a screwdriver and snap in the new one, took 1 minute because I replaced both of them.
Excellent fast delivery. 5 stars !

lower drawer drags on floor

  • Customer: columbus from birmingham, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
remove/pry broken plastic glide from in-side of oven,( wall not drawer ) and install new one.

Oven Pilot Heater Would Glow, Burner Would Not Light, Smell Of Lp Gas

  • Customer: JOHN from SOPCHOPPY, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 2 people found this instruction helpful
After reading the input of others on your site I ordered the igniter. Within a short time it was installed and the oven works fine. Thanks for the help, jc

Actually, the igniter I purchased is to be used on my furnace.

  • Customer: Lester from Waynesville, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 5 people found this instruction helpful
I have a Nordine model G2RC-105C19 LPG gas furnace. It was installed in 1995. The igniter went out and my son who was a propane gas appliance service tech installed one that was for our gas range. He said they were the same with the exception of a metal mounting plate on the stove igniter. Once the plate was removed, the igniter fit perfectly on the furnace. As a side note, the one I just bought from PartSelect was less expensive than one for the furnace.

Broken drawer glide

  • Customer: Pamela from Presho, SD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Glide just slipped out and the other in.So pleased at how fast the part arrived!! Less than a week.

Oven would not ignite because the ceramic was cracked off

  • Customer: Michael from Spring Grove, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 0 of 3 people found this instruction helpful
First i disconected the plug went right where the trouble was.removed the two screws and the safe plate that is protecting the wires.disconeted the two wires and replaced the new ignighter. put everythin back together tried it out ond guess what ??? it works .. Thank you
All Instructions for the TGF362BBBA
196-210 of 305