Models > TGC3X6XCB2

TGC3X6XCB2 Tappan Cooktop - Overview

Get Parts and Repair Help for TGC3X6XCB2

If you know the cooktop repair part you need, you can browse the list of all parts on the TGC3X6XCB2, or you can search by name or part description. You can also find your part by where it is located on the TGC3X6XCB2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your cooktop. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the TGC3X6XCB2 [Viewing 4 of 4]

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.93

Surface Burner Igniter Electrode

Use this igniter with sealed burners.

Order within the next 12 hrs and your part ships today!
$38.87

Spark Module

This part sends enough current to the igniter to create a spark to the bottom of the burner cap.

Order within the next 12 hrs and your part ships today!
$32.54

Igniter Switch

When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.

Order within the next 12 hrs and your part ships today!
$27.37

ORIFICE

Order within the next 12 hrs and your part ships today!
$19.18

Bushing

Order within the next 12 hrs and your part ships today!
$52.52

Burner Pan Gasket

Order within the next 12 hrs and your part ships today!
$128.13

VALVE

Order within the next 12 hrs and your part ships today!
$53.95

LP CONVERSION KIT

Order within the next 12 hrs and your part ships today!

Small Burner Base with Orifice and Igniter

This part also includes 3 screws. Small burner cap is sold separately.

Burner Cap - Black

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Igniter porcelain was cracked and burner would not light.

  • Customer: Rusty from Howell NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 37 of 51 people found this instruction helpful
un-pluged stove,removed the one screw holding the broken igniter. disconected the one wire. installed new igniter and slipped on wire. The igniter came with a new bracket, the old one rusted away which is why the old igniter broke. read more

Bad igniter.

  • Customer: chris from Venice CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 11 of 12 people found this instruction helpful
The stove was older so the burner was hard to get out. The small screw heads broke off, so I had to carefully center punch and drill out the screw bodies. The igniter screw was also frozen in the pot metal burner. That screw requied drilling and tapping with the installation of a new 6-32 screw. Once the burner was refurbished, the igniter mounted easily. ... read more

gas ignitor continued to run after turned on or off

  • Customer: Duff from Buena Vista CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
Removed all of the grates, control knobs and gas diffusers. Unscrew the drip pans, two on each pan, which attach the pans to the gas supply. Raised the drip pans from the top and unplugged the ignitors from all pans. Remove the top and the rubber deflector over the ignitor switch. The ignitor switch snaps off and on. One of the seals under the drip pan was b... read more