Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TEF361ESD > Instructions

TEF361ESD Tappan Range - Instructions

All installation instructions for TEF361ESD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF361ESD
316-330 of 494
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Hot Surface Light won't turn off.

  • Customer: Justin from Madison, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Unplugged stove. Quickly unscrewed back panel (4 screws). Popped the wires off one at a time attaching them to the new switch. Pulled the knob off the front, unscrewed screws, and put new switch in repeating previous steps in reverse. Put the panel back on, plugged it up, and pushed it back into place. Done.

Bake element went out & Large Burner would not cut off

  • Customer: Gene from Ethel, LA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
It was just a matter of loosing 2 screws on baking element & pulling 2 wires off & putting back on. On the Burner I had to take 6 to 8 screws off back 4 wires off & 2 screws on fron of switch. Very Easy!

broil element burn out

  • Customer: christopher from big pine key, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
take back planel off, take wires off old element and intsall new element hookup wires, put back planel ..under one hour job

eliment burnt out

  • Customer: Percy from Bryant Pond, ME
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
took off back cover unhooked wires. pulled out screws in the oven and removed the element. put in new element replaced screws reattached the wires in the back replace the back cover. Done

No heat to large coil; erratic heat with clicking noise to small coil

  • Customer: Mustafa from Pennsville, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I followed the Parts Select Video that showed replacing an identical switch. Mine were another brand & style with different color wires. I took a picture of 1 to keep track of the wiring and removed it. I saw that the terminals were marked P, H1, H2, L1, & L2 so I put the wire from the same terminal onto the Parts Select switches & they work just fine now. The parts I got from you are heavier and a much better quality than the original equipment. I would also like to say that I was amazed at how fast this order was shipped, and the washer pump was a piece of cake thanks to your video.

the baking element had separated (burnt out)

  • Customer: James from Pocahontas, AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
No directions come with the parts. I used a nut driver to unhook the connections on each side. The wire was connected with a male/female small connection ( they were inside the back of the oven. I pulled each one out and had to pry them loose with a screw driver. I attached each wire and used the nutdriver to tighten them. It was easier doing the repair than writing this explanation. I am not a handy man...

Needed to install an anti-tip bracket on my stove.

  • Customer: Daniel from Provo, UT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

Element cracked and not working

  • Customer: Marian from TOMS RIVER, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Using the video instructions, I had no problems with the installation. I was so proud of what I had done and the possible money I had saved that I told everyone I know. Thanks so much for your web site. As a matter of fact I found your site while looking for possible repair costs and your ad caught my eye. I am a 81 year old female, so if I can do it anyone can.

Baking Element on Bottom Broke

  • Customer: Paul from Pennsburg, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the Part Select installation video. Made it really easy.

My bottom baking element burned into.

  • Customer: Barb from Carlisle, OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was easy. Would have been super easy if a piece of the old element had not broken off in the slot. The directions that I received were perfect. The oven was fixed within 45 minutes. No repairman needed - very inexpensive fix. By ordering this part and following the directions it was a quick and cheap fix. Thank you for having my part and sending instructions with it. Barb T, Carlisle, Ohio

Large burner doesn't turn down or shut off.

  • Customer: James from Forestdale, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Followed video instructions on your web site.Removing one wire at a time as suggested simplified installation.Somehow i lost burner lens indicator.Ordered it from your website cost $3.84 plus shipping recieved in one day. GREAT SERVICE

Bake element burnt out

  • Customer: Matthew from Bellevue, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the repair video that came with my recipt for my order. When my bake element arrived I unplugged the stove. I then followed the instructions in the video by unscrewing the old element and removing the wires. I then hooked up the wires to the new element, pushed it into place and attached the screws. Plugged in the stove and turned on the over to preheat. Worked like brand new. PartSelect save me so much money and time. I love this site!

Bake element flared up and died

  • Customer: david from miami, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The most difficult part of the process was cleaning the oven. It possibly had never been cleaned before. It was cleaned while waiting for the part to arrive. The part came in 2 or 3 days and I got right to work. I had expected that the nuts might be frozen with rust to the back plate but the nut driver handled them with ease. I used clothes pins to prevent the wires from disappearing back through the holes in the back plate. The push pull connectors came off easily and went back on snug with no adjustment needed. Everything fit just fine and best of all, the oven can bake again.

oven was too hot code f-10 came up

  • Customer: Donnie from McLaughlin, SD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pulled out range, unplugged power used nut driver to remove back and removed oven probe. Had to change end and reinstalled in reverse order.

Switch was Sparking

  • Customer: Susan from Hillsboro, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
So simple....removed back panel, removed knob from front of range and removed 2 screws holding the knob in. Used needle nose pliers to pull wires off existing switch, placed wires in identical spots on new switch. Put switch post through front of range and put the 2 screws back in and the knob on. Finished and ready to go in less than 10 minutes. No more sparking....
All Instructions for the TEF361ESD
316-330 of 494