Models > TEF361ESC > Instructions

TEF361ESC Tappan Range - Instructions

All installation instructions for TEF361ESC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF361ESC
421-435 of 463
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Baking element quit working

  • Customer: Mimi from Hopwood PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I looked at the available online tutorial, followed the instructions given. It was an excellent tutorial and the repair was done in minutes. The element shipped quickly and the whole transaction was simple and cost effective!

bake element burned out

  • Customer: CHARLES from GEORGETOWN GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
was easy pulled out old one,pushed one hew one.

element blew up

  • Customer: Victoria from Alton IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I watched your repair video and this took no time at all, it was really easy. It took longer to find the right size socket and to clean the sides of the stove and underneath it after pulling it out than the repair took. Thanks!

Oven would not heat

  • Customer: tony from moreland GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Use the drawing and a meter found the was the problem the control board replaced board.

Heating element went out in oven.

  • Customer: Jerald from Hackett AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unscrewed two screws and unplugged the two wires took the old element out and replaced it with the new one plugged the two wires back in put it back in place and put the two screws back in place and I was done in less than 15 minutes.

baking element was not getting hot at the bottom of oven.

  • Customer: dolores from bridgewater NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
was so easy my husband told me we needed a new oven I went on this parts select website they told me everything! where to find model number to my oven what the part look like how to take out old and replace with new part. my husband was so impressed! I impressed myself!

Burner would stay on high when switch was on simmer

  • Customer: Dennis from Corpus Christi TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power first. Removed 4 screws on the back of the range, pulled the knob off of the switch, removed 2 small screws on the switch(on the front , under the knob) pulled off the 4 wires with spade connections on the switch. Put wires on the new switch, put in 2 screws on new switch, pushed knob on switch, replaced back cover and tested the new switch. Works great. Took less than 10 mins.

Baking Element Burned Out

  • Customer: Thomas from Lewisburg TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I removed the two screws at the back of the inside of the oven, pulled the element out to where I could remove the slip on fitting from each side of the element, the I connected the fittings to each side of the new element, pushed it back into place and then replaced the screw on each side of the new element to hold it into place.

oven element failed

  • Customer: Robert from Grand Island NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged range from power receptacle. Opened oven door to locate element. Using 1/4 inch nut driver,removed two mounting screws holding bottom element in place at back of oven. Pulled element forward to expose two(2) push-on terminals. Removed push-on clips from element terminals. Removed element from oven chamber and tested it for continuity. Determined that element had failed. Found part #on element and ordered new element on-line. Order placed on Sunday PM and part received just after noon on Tuesday. Installed new element which worked perfectly. Actual repair time about 20 min. 20

Bake element burned out

  • Customer: Jamal from Arizona City AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I followed the video on this website/youtube. Extremely ease.

Lower heating element burnt out

  • Customer: Sandy from Marshall MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Super easy, was putting it back together when husband got home from work and decided that he needed to finish putting the last screw in

Heating element burnt out.

  • Customer: Andre from LaGrangeville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just like the video showed, I unscrewed the old element, and screwed in the new one. Really that easy!

oven would turn on and stay on regardless of set point

  • Customer: robert from Mansfield MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pulled oven from counter space unplugged unit unscrewed 9 - 1/4" tech screws then one more 1/4" tech screw that holds the sensor.Inserted the new element cut the two wire because it was a different connection stripped the wires and did the same to the old element but used the old plug.Connected the plug,plugged the over back in slid the unit back and turned out on for a test.All is well,thank you!

Heating element burnt out.

  • Customer: Veronica from Port St Lucie FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Take off nut and cover at rear off oven, both sides. Pull old element off (push on plug). Put replacement element in oven push on to wire plug, make sure it is on tightly. Push into oven wall, secure by replacing nut and cover. Your Job is complete.

LED Light Infinite control LED indicator blown

  • Customer: Christopher from Rock Port TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed back, identified faulty parts and next aired replacements. Easy job with screw gun and needle nose.
All Instructions for the TEF361ESC
421-435 of 463