Models > TEF351EWB > Instructions

TEF351EWB Tappan Range - Instructions

All installation instructions for TEF351EWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF351EWB
451-465 of 491
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

baking element was not getting hot at the bottom of oven.

  • Customer: dolores from bridgewater NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
was so easy my husband told me we needed a new oven I went on this parts select website they told me everything! where to find model number to my oven what the part look like how to take out old and replace with new part. my husband was so impressed! I impressed myself!

Burner would stay on high when switch was on simmer

  • Customer: Dennis from Corpus Christi TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power first. Removed 4 screws on the back of the range, pulled the knob off of the switch, removed 2 small screws on the switch(on the front , under the knob) pulled off the 4 wires with spade connections on the switch. Put wires on the new switch, put in 2 screws on new switch, pushed knob on switch, replaced back cover and tested the new switch. Works great. Took less than 10 mins.

Baking Element Burned Out

  • Customer: Thomas from Lewisburg TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I removed the two screws at the back of the inside of the oven, pulled the element out to where I could remove the slip on fitting from each side of the element, the I connected the fittings to each side of the new element, pushed it back into place and then replaced the screw on each side of the new element to hold it into place.

oven element failed

  • Customer: Robert from Grand Island NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged range from power receptacle. Opened oven door to locate element. Using 1/4 inch nut driver,removed two mounting screws holding bottom element in place at back of oven. Pulled element forward to expose two(2) push-on terminals. Removed push-on clips from element terminals. Removed element from oven chamber and tested it for continuity. Determined that element had failed. Found part #on element and ordered new element on-line. Order placed on Sunday PM and part received just after noon on Tuesday. Installed new element which worked perfectly. Actual repair time about 20 min. 20

Bake element burned out

  • Customer: Jamal from Arizona City AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I followed the video on this website/youtube. Extremely ease.

Replace terminal block and burner unit.

  • Customer: James from Williamsville VT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very simply following the online video instructions.

Lower heating element burnt out

  • Customer: Sandy from Marshall MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Super easy, was putting it back together when husband got home from work and decided that he needed to finish putting the last screw in

Heating element burnt out.

  • Customer: Andre from LaGrangeville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just like the video showed, I unscrewed the old element, and screwed in the new one. Really that easy!

oven would turn on and stay on regardless of set point

  • Customer: robert from Mansfield MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pulled oven from counter space unplugged unit unscrewed 9 - 1/4" tech screws then one more 1/4" tech screw that holds the sensor.Inserted the new element cut the two wire because it was a different connection stripped the wires and did the same to the old element but used the old plug.Connected the plug,plugged the over back in slid the unit back and turned out on for a test.All is well,thank you!

Heating element burnt out.

  • Customer: Veronica from Port St Lucie FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Take off nut and cover at rear off oven, both sides. Pull old element off (push on plug). Put replacement element in oven push on to wire plug, make sure it is on tightly. Push into oven wall, secure by replacing nut and cover. Your Job is complete.

LED Light Infinite control LED indicator blown

  • Customer: Christopher from Rock Port TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed back, identified faulty parts and next aired replacements. Easy job with screw gun and needle nose.

The oven element just went to pieces.

  • Customer: HAROLD from ASHLAND OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I pulled the stove out away from the wall and unplugged it from the wall. I then proceeded to take all the screw/nuts out and disconnected what was left of old element and put new element through holes in back and put on the connectors and reinstalled the back and plugged it in and turned on the oven and it worked like a dream. Thanks PartsSelect for the speed and effiency of getting me part to me.

my bake element broke

  • Customer: Patricia from Manchester CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I order the part from you which I got in 1 day great shipping. took out the part and rescrewed the part in done in 5 mins would order again from you and recommend to all

baking element was out

  • Customer: james from OCOEE FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed old baking element and replace new base baking element very very easy

shorted out small element burner switch

  • Customer: Alvie from Walnut Cove NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First, I disconnected the electrical power by pulling apart the plug behind the range. Next, I removed the screws holding the service plate on back of the top panel.I removed the switch knob by gently pulling it from the stem. Underneath I found 2 screws holding the switch in the panel. I removed these with a phillips screwdriver.I was able to pull the entire switch out to the rear leaving all wires attached.The new switch looked different from the original and the wires were configured differently but the wires were clearly marked. By removing one at a time and placing it on the new switch to the corresponding marking,it was a simple matter to wire the switch.I reinstalled the switch in the panel,put back in the screws to hold the switch, slid the knob back on the stem, reinstalled the rear panel,and plugged the power cord back in.The switch worked perfectly.
All Instructions for the TEF351EWB
451-465 of 491