Models > TEF326FSD > Instructions

TEF326FSD Tappan Range - Instructions

All installation instructions for TEF326FSD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF326FSD
511-525 of 664
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

element burned out

  • Customer: james from oscoda MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
watched the video online that was provided. made the job very easy. anyone could do it. works great. thanks.

old oven racks were nasty!

  • Customer: Richard from Fort Wayne IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We recently purchased condo and WhiteWestinghouse range needed some love. the old racks were not in very good shape so we ordered new.

element burnt out

  • Customer: Edward from Inverness FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
two screws and plugged back in works great

drawer glides broken

  • Customer: robert from toms river NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
poped out the old ones and new ones slide right in.

Bottom Element burned out

  • Customer: Jon from Clay Center KS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First, I UNPLUGGED the range. After removing the screws that hold the element in I pulled it out, disconnected one side, then tried to disconnect the other side only to find it soldered on. With the diagonal pliers I cut wire next to where the terminal was connected to the element. Using the crimping tool I stripped the end to expose about 1/4 inch of clean wire, twisted it tight, put on a new terminal, crimped it in place and pushed it on the element. After that, all I had to do was push the element back in place and secure it with the screws. The last step was to reconnect the power and turn the oven on low heat for about five minutes to burn off any residue on the element. Works great! Thank you

The Element burned out

  • Customer: Yvonne from Spring City PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I turned the breaker off first of course. Then I removed the oven racks and removed the metal tabs by unscrewing the hex nut with the nut driver. I pulled the wires in to the oven and unsnapped them from the element. I bet them so that they would not go back through the hole. I removed the broken element and snapped in the new element. I pushed the wires back through the holes and lined up the metal tabs. I put the hex nuts back in and screwed them in tight. Turned the breaker back on. Set the oven to 350 and turned it on. I could feel the heat at once. Ta-DA!

Oven would not heat

  • Customer: Ken from Carson City NV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Diagnose if element or controller by removing element and turning oven on. Found voltage at wires, so assumed controller OK. Check resistance/continuity of element. Appeared open (don;t what actual value should be (neglected to check new part). So pretty sure it was element. Left disassembled while ordering new part (use of range top ok - no oven use) replaced element, function check OK. Done.

Storage drawer was hanging down.

  • Customer: Michael from Midlothian VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Followed the instructional video , removed the drawer, popped out the damaged part, inserted the new part, replaced the drawer. Didn't need any tools and the job took less than 10 minutes to do.

no problem

  • Customer: Janis from Groton CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was easy. My comment however is about the young lady that helped me with the return. I order the wrong part and when it came in, it didn't fit. I called for help returing the part and she was kind enough to help me order the right part, which I didn't think she would do. I made it so I will definately use this company again and reccomend you to my family and friends.Thank you, Janis Krotsis

My fiancee was baking when she heard a pop and saw a spark from the clock. When I looked at it the clock and timer were dead and the oven wouldn't work but the top burners worked.

  • Customer: Joe from Bowling Green KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I read some other's repairs from this site with similiar symptoms. Take off the back takes a couple of minutes. Turn off power at the breaker of course the range is 220 volts. Remove the 4 screws holding the clock timer. Carefully remove the clock front as not to damage it. It has a flexible glue that holds it. You may need to take a knife to get it started. Line it up and stick it on the new clock timer, there will be plenty of glue left to hold it. Remove wires one at a time and place them on the new board as you go until you have all leads changed to the new board. Put the new timer in place and insert the 4 screws that hold it.Turn it on and the clock should be flashing. Reset the clock and you should be ready to go! I turned on the oven and it worked! I saved myself a about $250 by doing it myself. $85 for a service call and whatever they would decided to mark up for the clock timer. 20 minutes start to finish. It really was an easy fix!

element would not heat.

  • Customer: Arnold from Carlsbad CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the control I got from you , even though it was a little different the lugs matched up and works great.

My bake element burned out

  • Customer: Michael from Klamath Falls OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My bake element stopped working and found part of it burned. So I ordered a new one and received it in a week. It took about 2 min. to remove the old and install the new one and I'm back baking.

baking element broke

  • Customer: TRAVIS from BLOOMINGTON IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplugged stove;used nut driver to unscrew 2 screws and remove broken element;plugged in new element;used nut driver to replace screws. done. i used a flashlight to see better in oven. easy

broken drawer glide

  • Customer: tom from duluth MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I am a total non repairman. but with the video on how to I did'nt even brake the first part. ( I ordered 2 just in case)Will use you ror every part!

When turning the switch on for the large eye I could hear an electrical short behind the switch.

  • Customer: Kent from McHenry MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Initially we realized there was a problem while cooking with the large eyes and we began hearing an electrical short behind the control switch. I unplugged the power from the oven/cooktop and removed the back panel where I could visually see soot on the switches where it was shorted. Careful while choosing your part from the diagram on Partselect.com. For the model FEF336ECJ, atleast for my oven, the eye switches were reversed and I ordered the small eye's switches! Luckily they have an outstanding customer support and immediately mailed out the new parts and a label to send the wrong parts back. Changing the parts out was very simple. Pull the oven out and UNPLUG IT from any electrical outlet. Remove the back panel. Double check from the label on the front of the control panel that you are working with the correct switch, and before removing the current switch, remove the wires one by one and place them on the new part to make sure you don't misplace these wires. Once the wires are connected to the new part, pull the plastic knob off of the old switch to reveal the screws on front of the panel. Place the new switch where the old one came from and fasten the screws back in place. Replace the knob, replace the back panel(for safety) and test the new switch before you push the oven back into place. If you can turn a screw driver, move the oven, and unplug the power, this easy do it yourself repair will save you possibly hundreds by not calling a repair/handyman who would absolutely love you to pay out the nose for such an easy task.
All Instructions for the TEF326FSD
511-525 of 664