Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TEF326FSC > Instructions

TEF326FSC Tappan Range - Instructions

All installation instructions for TEF326FSC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF326FSC
631-645 of 673
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burnt out element

  • Customer: pascale from bridgewater, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Simple. Unscrew 2 screws unplug 2 tabs. Push on 2 tabs. Put 2 screws back adjust feet.

The Bake element broke

  • Customer: Daphne from Henrico, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband did the repair he removed the old element and replaced it with the new one it was very easy to replace.

Element failed to heat

  • Customer: Jeff from Berwick, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Piece of cake! Unscrewed the old, pulled it out, & put in the new element. Turned the oven on & presto! Oven can now bake!

Lower level heating element

  • Customer: Debbie from Missoula, MT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy as one two three. Snap electrical wires to new element push thru back wall of oven and turn screws tight. This company was so amazing and my order arrived in a few days. I found you on the internet. Bless you all .

Replaced heating element

  • Customer: Sheila from Monticello, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I went to video and followed instructions. I removed the holding brace securing the element in and pulled out old heating wire and installed new one that came a day after I ordered it. It was so easy and saved me over $100

bad burner switch

  • Customer: ALBERT from LITCHFIELD, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine

So easy!

  • Customer: Patricia from Newburgh, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First off the shipping was lightning speed and the repair was super easy anyone can do it.

Old element broke

  • Customer: Deborah from Varna, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
All I did unscrew bolts pull out element wires detach them attach new element to the wires push them back inside the openings reattach bolts all done easypeasy and I am a 63 yr old woman

rear guide clips were broken

  • Customer: Audrey from Miami, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
This was the easiest do it yourself repair job to be had so simple just push the new clip in the hole and you are done so easy. Audrey

Bad element

  • Customer: Darlene from Allons, TN
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed screws,pulled off clips,reinstalled new element.

heating element out

  • Customer: Elsie from Commerce City, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took to screw out pull to wire's out push to wire's back on put the screw back on complete less than 5minutes

Temp did not match readout.

  • Customer: John from Columbiana, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced temp probe and checked OK. This model did not have a full back as the instructional video showed. No cover to remove at all. Only suggestion might be to include two wire nuts of proper size. Average wire nut would be too big. Fortunately, I happened to have a couple.

Bake Element in Oven

  • Customer: Timothy from Titusville, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Quite easy and takes 5 minutes Remove racks from oven. Use a phillips screwdriver and remove 1 screw from each side of baking element. Gently pull baking element slowly or carefully so you do not damage wires, insulation around wires or so they don't come off element before you can reach them. With a pliers, hold the metal clip attached to wire and pull off of baking element. Make sure wire will not go back into back of stove. Pull off opposite side wire in same manner. Take new element, check the orientation of the element, make sure it it going in correct, and slide wire clip onto one end of element. Do the same thing with the other wire on opposite side. Carefully feed wire back into openings in oven while placing element back in oven.. Replace screws on each side of element to hold in place. Turn oven on so make sure it element is heating. I left my oven on 400 degrees to burn off anything that may have been on the new element during manufacturing so it would not leave or transfer an odor to food when using the next time.

wrong temp when baking.

  • Customer: John from Hiawassee, GA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
removed back. discovered wrong connector on probe. Cut the connectors off and spliced with small butt connector. Took me longer to find the tools and connector than to do the repair. The wires are very small and require a very small butt connector. Tips by the sales rep and previous customer were helpful. Great service. Will try PartSelect for Cub Cadet and Yamaha OB parts. Thanks. John

My burner would stay on high regardless of where it was set.

  • Customer: Smtella from Wappapello, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
We removed the back of the stove, unscrewed switch from the stove face and unplugged the wires from the old switch. The new switch was universal so I had to follow the numbers by the prong on the old switch to determine which was the correct prong to plug the wires, plugged them in, screwed the switch back to the stove face and replaced the back Viola all fixed.
All Instructions for the TEF326FSC
631-645 of 673