Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TEF326FSB > Instructions

TEF326FSB Tappan Range - Instructions

All installation instructions for TEF326FSB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF326FSB
631-645 of 675
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Element failed to heat

  • Customer: Jeff from Berwick, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Piece of cake! Unscrewed the old, pulled it out, & put in the new element. Turned the oven on & presto! Oven can now bake!

Lower level heating element

  • Customer: Debbie from Missoula, MT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy as one two three. Snap electrical wires to new element push thru back wall of oven and turn screws tight. This company was so amazing and my order arrived in a few days. I found you on the internet. Bless you all .

Replaced heating element

  • Customer: Sheila from Monticello, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I went to video and followed instructions. I removed the holding brace securing the element in and pulled out old heating wire and installed new one that came a day after I ordered it. It was so easy and saved me over $100

bad burner switch

  • Customer: ALBERT from LITCHFIELD, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine

So easy!

  • Customer: Patricia from Newburgh, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First off the shipping was lightning speed and the repair was super easy anyone can do it.

Old element broke

  • Customer: Deborah from Varna, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
All I did unscrew bolts pull out element wires detach them attach new element to the wires push them back inside the openings reattach bolts all done easypeasy and I am a 63 yr old woman

rear guide clips were broken

  • Customer: Audrey from Miami, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
This was the easiest do it yourself repair job to be had so simple just push the new clip in the hole and you are done so easy. Audrey

Bad element

  • Customer: Darlene from Allons, TN
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed screws,pulled off clips,reinstalled new element.

heating element out

  • Customer: Elsie from Commerce City, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took to screw out pull to wire's out push to wire's back on put the screw back on complete less than 5minutes

Temp did not match readout.

  • Customer: John from Columbiana, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced temp probe and checked OK. This model did not have a full back as the instructional video showed. No cover to remove at all. Only suggestion might be to include two wire nuts of proper size. Average wire nut would be too big. Fortunately, I happened to have a couple.

Bake Element in Oven

  • Customer: Timothy from Titusville, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Quite easy and takes 5 minutes Remove racks from oven. Use a phillips screwdriver and remove 1 screw from each side of baking element. Gently pull baking element slowly or carefully so you do not damage wires, insulation around wires or so they don't come off element before you can reach them. With a pliers, hold the metal clip attached to wire and pull off of baking element. Make sure wire will not go back into back of stove. Pull off opposite side wire in same manner. Take new element, check the orientation of the element, make sure it it going in correct, and slide wire clip onto one end of element. Do the same thing with the other wire on opposite side. Carefully feed wire back into openings in oven while placing element back in oven.. Replace screws on each side of element to hold in place. Turn oven on so make sure it element is heating. I left my oven on 400 degrees to burn off anything that may have been on the new element during manufacturing so it would not leave or transfer an odor to food when using the next time.

bottom element

  • Customer: James from Surrency, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
1/4" nut driver, just took the screws out disconnect the element. Reversed the process. Really easy. and outstanding delivery.

Lower bake element broke in two.

  • Customer: John from Elko, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Either disconnect power plug or shut off breaker to oven. Remove racks from oven. Remove the two screws from back of oven that hold element. CAREFULLY pull the ends of element from back of oven so as not to loose the connected wires. Disconnect wires from element terminals. (Be careful not to allow the wires to fall into the backside of oven) Reattach wires to the new element, carefully insert through the holes and reinstall screws.

Bottom heating element burned out. Oven would not heat up.

  • Customer: William from Cynthiana, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Safety first. Turn the breaker off. This repair is so easy. Remove the two screws at the back of the oven. The heating element will pull out about 2 inches. Disconnect the heating element from the terminals. Plug the new heating element back in. Reinstall the screws. Turn the breaker back on. Your finished. This repair probably saved me $100.00 for a service call and parts.

The electri oven element burned out and needed relaceing

  • Customer: Lancelot from Jonesboro, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the online video and it worked out just as it said. I unscrewed the contact bolts, disconnected the contacts, ( they were a little corroded but eventually came out with a little persistence and effort) and reconnected the new element, and ...Voila!!! It worked Be sure to to turn off the power before beginning the job.
All Instructions for the TEF326FSB
631-645 of 675