Models > TEF326FSB > Instructions

TEF326FSB Tappan Range - Instructions

All installation instructions for TEF326FSB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF326FSB
496-510 of 666
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not heating

  • Customer: Steve from lake Hiawatha NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed oven from wall, disconnect power source, loosen nuts from element, pull element out, disconnect wires, hook up wires to new element, put back nuts.Plug in and it worked great.

No heat from bottom or top element,k stove top and clock all worked fine.

  • Customer: steven from Daleville AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.

Just had to replace the racks in the stove.

  • Customer: charles from El Paso TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks

Bake element burnt out

  • Customer: Elizabeth from Houston TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Disconnected power; unscrewed element from oven wall; pulled element off of contacts. Pushed new element onto contacts; screwed to oven wall

Bake element caught fire and stopped working

  • Customer: Megan from Savannah GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
After in I found my oven glowing from the small fire inside, I thought I was in for an expensive repair or complete replacement. Part select helped me find the exact part I needed and the video showed me just how easy it would be. $40 and 15 min later my oven was fixed and I was baking again! The repair consisted of removing two screws and simply removing and plugging in the new bake element. Thanks for the help!!

Oven Temperture probe.

  • Customer: Kenneth from Edgemount SD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Would have been simple if Frigidare had not changed the plastic snap wire connector on the part. The replacement part had a different snap together wire connection. After a couple of phone calls stating that the new part and the old part had different part numbers was informed that you have to snip off the ends and use wire connects but it was the right part. Once I knew that it was a simple repair if you have the wire connects to connect the wires.

replace oven element

  • Customer: Cathy from Farmersburg IN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
good

oven element not working

  • Customer: Patricia from Hendersonville NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old element and just popped in the new one

Heating element , not heating

  • Customer: Joseph from Littleton NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
1. Made sure replacement part matched the defective part. 2. Got the recommended tools. 3. Pulled out range away from wall. Unplugged range. 4. Opened oven door and removed two screws ( with nut driver ) that hold heating element and detached the two wires from the element with pliers. Threw away old element and than connected the two wires ( one to each end of the new heating element ) . Than I use the nut driver to secure the new element with the two screws I removed earlier. Plugged range back in and pushed it back against the wall. Than turned on oven and the oven heated very well. Less than 15 minutes to complete the task.

Bake element needed replacement

  • Customer: Paula from Cazenovia NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Piece of cake mostly because the video was very helpful clear and thorough

Oven bake element burned out

  • Customer: Charles from Saint Augustine FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced element

The lower oven heat element went out

  • Customer: Jim from Webster WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I went on line and looked up our Model no and serial number of our Frigidaire Range, on Part Select's website, found the part and ordered. Within 3 days the part arrived, and to work on the lower heat element, the two oven racks are removed then I used a small socket set to take the connecting screws out, pull the bake element out of the socket, remove the power cords, then reverse the process install the power cords(just easy slip on) and then reattach the screw, tighten, and put the two over racks back in their place. Turn the oven on and the oven worked beautifully.

front left burner was on HI no matter what the dail setting was

  • Customer: Eric from Mosier OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
pull back panel, 2 screws & one wire at a time.....And don't forget to KILL POWER!!!!super easy works great now and the wife loves it.

my bake element was sparking it was cracked

  • Customer: JAMIE from SAVANNAH GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
used fill up screw driver removed bake element, detaching it from power wires on both ends replaced it with new bake element screwed back in and was done in 5 minutes.

The Bake Element burned out and broke

  • Customer: Deneice from Guilford MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I unplugged the stove. I used a nut driver to remove the element from the back of the oven. The ends of the element were attached to wires. I pulled the ends of the element out of the wire ends, being careful to hold on to the wires to protect them from breaking. I pushed the wire ends onto the new element, fed the wires back into the back of the oven, put the screws back in and it was done! The repair was very simple. The hard part was cleaning under the stove and the sides of the stove!! :) When I pulled it out to unplug it I found that my children love to sweep things underneath it!! Oh well now I have a working oven AND a clean stove!
All Instructions for the TEF326FSB
496-510 of 666