Models > TEF326FSA > Instructions

TEF326FSA Tappan Range - Instructions

All installation instructions for TEF326FSA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF326FSA
616-630 of 680
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burner would stay on high when switch was on simmer

  • Customer: Dennis from Corpus Christi TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power first. Removed 4 screws on the back of the range, pulled the knob off of the switch, removed 2 small screws on the switch(on the front , under the knob) pulled off the 4 wires with spade connections on the switch. Put wires on the new switch, put in 2 screws on new switch, pushed knob on switch, replaced back cover and tested the new switch. Works great. Took less than 10 mins.

Baking Element Burned Out

  • Customer: Thomas from Lewisburg TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I removed the two screws at the back of the inside of the oven, pulled the element out to where I could remove the slip on fitting from each side of the element, the I connected the fittings to each side of the new element, pushed it back into place and then replaced the screw on each side of the new element to hold it into place.

oven element failed

  • Customer: Robert from Grand Island NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged range from power receptacle. Opened oven door to locate element. Using 1/4 inch nut driver,removed two mounting screws holding bottom element in place at back of oven. Pulled element forward to expose two(2) push-on terminals. Removed push-on clips from element terminals. Removed element from oven chamber and tested it for continuity. Determined that element had failed. Found part #on element and ordered new element on-line. Order placed on Sunday PM and part received just after noon on Tuesday. Installed new element which worked perfectly. Actual repair time about 20 min. 20

Bake element burned out

  • Customer: Jamal from Arizona City AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I followed the video on this website/youtube. Extremely ease.

Replace terminal block and burner unit.

  • Customer: James from Williamsville VT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very simply following the online video instructions.

Lower heating element burnt out

  • Customer: Sandy from Marshall MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Super easy, was putting it back together when husband got home from work and decided that he needed to finish putting the last screw in

Heating element burnt out.

  • Customer: Andre from LaGrangeville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just like the video showed, I unscrewed the old element, and screwed in the new one. Really that easy!

Heating element burnt out.

  • Customer: Veronica from Port St Lucie FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Take off nut and cover at rear off oven, both sides. Pull old element off (push on plug). Put replacement element in oven push on to wire plug, make sure it is on tightly. Push into oven wall, secure by replacing nut and cover. Your Job is complete.

Oven and broiler would not work

  • Customer: Joyce from Donalds SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed old screwed on the new one. It was done!

Front glider ( plastic) on bottom oven drawer was proken.

  • Customer: CAROL from salt Lake City UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took the new plastic glider out of the bag and it took me about 2 minutes to fix the drawer!!! EASY!!!!! Thanks. carol

oven elements would not heat up

  • Customer: Kristie from Glenmoore PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took off back of oven, detached old clock piece, attached new one, put back panel back, done.

LED Light Infinite control LED indicator blown

  • Customer: Christopher from Rock Port TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed back, identified faulty parts and next aired replacements. Easy job with screw gun and needle nose.

The oven element just went to pieces.

  • Customer: HAROLD from ASHLAND OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I pulled the stove out away from the wall and unplugged it from the wall. I then proceeded to take all the screw/nuts out and disconnected what was left of old element and put new element through holes in back and put on the connectors and reinstalled the back and plugged it in and turned on the oven and it worked like a dream. Thanks PartsSelect for the speed and effiency of getting me part to me.

WELD WAS BROKEN ON SUPPORT BRACKET ON ELEMENT

  • Customer: GEORGE from ADAMSVILLE OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
REPLACED ELEMENT NO PROBLEM?

my bake element broke

  • Customer: Patricia from Manchester CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I order the part from you which I got in 1 day great shipping. took out the part and rescrewed the part in done in 5 mins would order again from you and recommend to all
All Instructions for the TEF326FSA
616-630 of 680