Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TEF326FBC > Instructions

TEF326FBC Tappan Range - Instructions

All installation instructions for TEF326FBC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF326FBC
616-630 of 653
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

comp board went bad

  • Customer: Brian from King George, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy to do take the computer out. Had it done in about 2 minutes. Very simple use a drill with screw driver tip makes quick work. Plug the board back in button it all up oven works great.

Control Rod On Switch Was Broken Off

  • Customer: Richard from Williston, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I looked at video and followed the instructions from the man in the video. I pulled out range and then unplugged range from electrical outlet. I removed screws from back and took back off. I then took the two screws out from front of switch. I pulled switch out and then removed one of the wires off and placed it in the same place on the new switch. I did same on the other two wires. I then put switch back in place and tighten the two screws on front. I replaced the back on the range. I plugged range back into the receptacle, pushed range back in place. I put control knob on and then turned it on. The eye worked fine. Very easy!

Infiniti switch needed to be changed.

  • Customer: Ralph from Peoria, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Quit after getting shocked. New part had different configuration. Hard to see marking for pull and plug from old switch to new switch. New switch had different configuration. After all that and making sure switch worked, got shocked as stove was pushed back to wall. Some other issues with wiring has a shorting out problem. Maybe time to call a pro or get rid of the stove and get the gas stove we have been longing for. Be sure to match points on pulling and plugging as the configuration may be different.

The burner coil had been broken

  • Customer: elizabeth from Pasadena, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just plugged it in! The hardest part was finding the model number. It was inside the top of the stove,while cleaning, I found it-on the left hand side when you take out the burner pans. I searched this site, found the part and when it arrived I just plugged it in and it worked fine. I would say less than 5 minutes to fix this issue.

heating element no longer worked

  • Customer: Maryann from Roberts, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
pulled out the range and unplugged the range from the outlet! removed the oven racks. unscrewed the heating element and pulled out the wire connections a bit so i could grasp the connectors better and so they would not go back into the holes. getting the bad element off the connectors was the most difficult part of the process - this is what took the longest for me. I used pliers to grab the heating element connector and wiggle until it came loose from the connectors. once off, it was pretty simple to re-connect the replacement element and tuck everything back and screw the element back onto the oven wall. WA-LA!! back in the baking business - kids and mom are happy again! temp needs calibrating, but should be able to figure that out....thanks much!

Burner would no turn off.

  • Customer: ALBERT from BENTONVILLE, AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
A Phillips screwdriver and pliers were all the tools required. At first glance, the physical appearances of the OEM and the replacement were not identical. The slide-on electrical tabs were numbered on each in the same way. Sliding off the connectors and re=connecting them on the same number tab on the new switch was all there was to it.

could not control the heat cooking

  • Customer: Robert from HOLTSVILLE, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
removed six nutdriver screws and removed rear cover. the only problem i had was the new switch they sent was a little larger then the orig.had to figure out the wires. fit good and works perfect.

Bake element

  • Customer: Russ from Avondale, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Got the part,very affordable quick shipment,put it in plugged in the wires...Done! Thank you, getting parts from you for my ice maker as well!

Bake Element Shorted Out

  • Customer: Lisa from North Port, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
- Cut the power to the oven (I used breaker). - Unscrew 2 screws. - Disconnect from 2 electric terminals. - Remove old bake element. - Connect new bake element to 2 electric terminals. - Screw the 2 screws back on. - Turn the breaker back on. ------------------------------------------------> Done! . . Saved the $79 that the appliance guy would've charged just for diagnostics. The part shipped to me within 24 hours so I didn't have to worry about scheduling a 2nd appointment and waiting around with no oven. You can do this on your own! Thanks partselect.com :)

Burnt out element

  • Customer: pascale from bridgewater, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Simple. Unscrew 2 screws unplug 2 tabs. Push on 2 tabs. Put 2 screws back adjust feet.

The Bake element broke

  • Customer: Daphne from Henrico, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband did the repair he removed the old element and replaced it with the new one it was very easy to replace.

Element failed to heat

  • Customer: Jeff from Berwick, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Piece of cake! Unscrewed the old, pulled it out, & put in the new element. Turned the oven on & presto! Oven can now bake!

Lower level heating element

  • Customer: Debbie from Missoula, MT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy as one two three. Snap electrical wires to new element push thru back wall of oven and turn screws tight. This company was so amazing and my order arrived in a few days. I found you on the internet. Bless you all .

Replaced heating element

  • Customer: Sheila from Monticello, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I went to video and followed instructions. I removed the holding brace securing the element in and pulled out old heating wire and installed new one that came a day after I ordered it. It was so easy and saved me over $100

bad burner switch

  • Customer: ALBERT from LITCHFIELD, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine
All Instructions for the TEF326FBC
616-630 of 653