Models > TEF326FBB > Instructions

TEF326FBB Tappan Range - Instructions

All installation instructions for TEF326FBB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF326FBB
466-480 of 664
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

element made a loud noise then caught on fire.

  • Customer: teresa from rosehill, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the online video instructions.Thanks for the step by step online video.

Replaced large burner switch on tappan range

  • Customer: thomas from Huntington Station, NY
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I am an electrician so I had no problem identifying wire and connecting them properly. However there were no instructions provided with the part and the configuration of the new switch was different than the the old one. I doubt if a DIY individual would have been capable of handling this task. Also there were no safety warning with respect to electrical repairs, which is a must today.

Large Burner On Glass Top Quit Working

  • Customer: JILL from VIRDEN, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took the back off and replaced the switch for that burner. Got alittle nervous because the switch did not look the same and the connectors were labeled differently, but it worked. Lost the red light button some how during the repair so when I turned the stove on sparks came out the back because the light connector was loose so I did have to order another one of those.

Old rusty worn out oven racks

  • Customer: June from Mt. Vernon, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the old oven racks and put in the new ones.

My bake element had burnt out.

  • Customer: sandy from richmond, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
The element was relatively simple to put back on. While holding the connecting end coming from the back of the stove into the oven. I pushed the new element into the connector. It went in place perfectly.

the bake coil broke

  • Customer: angie from lake stevens, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video that was posted on the parts website when I ordered my part for my oven and it was sooooo simple now I'm back to cooking and my part was to my door in1 day after I order would definetly use this company again.

Element burnt into

  • Customer: Stacey from Abingdon, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Used a nut driver to remove old bake element and removed slide on clips on each side took the old pieces to trash and the put new element in by installing slide on electrical connection the tightened up screws with nut driver it was easy and the best thing was ordering of the part and getting the correct part in a timely fashion. I wish all websites were this efficient.

Gasket In Door Replaced

  • Customer: James from Greenville, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.

Oven would not heat.

  • Customer: Nanci M from Greenwood, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turned the main power off to my oven. Got my part removed two screws took the old bake element out put the new one in, replaced screws, turned power back on and boom it was fixed. Thanks so much for making it so easy.

Burner not working

  • Customer: timothy from Kingsland, GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Replace the switch in the control panel. Had to take off the back of the range and remove the electrical conection and then pull the switch by unscrewing the screws that hold it into place. The n replacing the switch and then reconnecting the wires then testing. Worked fine.

55 yr old wall oven had burnt out seal

  • Customer: Diane from Natrona Heights, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket

Element burned out

  • Customer: RICHARD from CORAM, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Removed two screwa holding element in place. Removed the connecting wires. Attached wires to new element. Reset emlement, replaced the screwa and I was done. Actuallt, I did as exactly as indicated in your film discribing the installation. P.S.-Part arrived in two days inspite of the impending hurrican. Extremely satisfied.

Burnt-out bake element

  • Customer: Henry from Stow, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My wife had seen a small fire in the bottom right of our oven, and I quickly turned off the oven unit, which put out the fire. We tested the oven a couple more times after it had cooled and determined that indeed the bake element had burned out. I'd used PartSelect before and been very pleased with their service (speed, ease of use of site, etc.,etc.) so I ordered a new bake element, which arrived in two days! It was easy to replace: I turned off the circuit breaker, slid the oven out from the wall, disconnected the plug, and then got to work undoing the tabs that hold the bake element to the rear wall. The only little glitch was that the screw heads on our range were neither slot nor Philips - they turned out to be small square-socket screws. I couldn't see that until I turned a bright flashlight on the job. Then it was a simple matter of trading out the screwdriver bit, disconnecting the old element, plugging in and attaching the new one, and away we went. Oven as good as new! Thanks, PartSelect!

element broken in half

  • Customer: James from Dallas, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
followed the video provided and installed it as instructed. Video and instructions provieded were very helpful

Heating Element broke

  • Customer: Jennifer from Columbia, MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Remove bolt from both ends of element carefully as not to damage wires connected to the ends. Replaced with new element. Simple.
All Instructions for the TEF326FBB
466-480 of 664