Models > TDG336RBW1 > Instructions

TDG336RBW1 Tappan Dryer - Instructions

All installation instructions for TDG336RBW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TDG336RBW1
196-210 of 241
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken belt; Second one in 2-years.

  • Customer: Edward from Sayville NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I heard the dryer running, but I didn't hear it tumbling like usual, so I got suspicious. I popped the top off of the dryer to reveal a broken belt. Installation took 20 minutes.

Lint filter overworked

  • Customer: Michael from Lanham MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Screw driver two screws and 25 sec.

Dryer just barely got warm

  • Customer: J Martin from Guerneville CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Everything I needed to know was already on your website. Prying off the top of the dryer (with a big screwdriver under the front of the top) was the hardest thing, since I was afraid I would break something. Only then can the front be removed (taking out just 2 phillips screws). The rest is easy.

The lint trap was destroyed

  • Customer: Tina from Burlington WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was extremely simple; put the screen part into the frame part and screwed in two (2) screws. It took me less than five (5) minutes. However, I was upset with the UPS delivery because I am disabled and he left it at the end of my driveway. I have never had a delivery left at the end of my driveway - they always come to my back door even if they've never been to my home before. I know it is not PartSelect's fault however, maybe they could speak to UPS for future disabled customers. I know this would be a deal breaker for me if I need another part. It is extremely difficult for me to walk to the end of my driveway.

Dryer lint trap was falling apart

  • Customer: garrett from Oklahoma City OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I just changed the lint trap. the amazing thing was that I ordered the part one afternoon to be delivered USPS and figured I wouldn't see it for weeks. BAM! the next day I got this part in the mail. it was kinda weird. Are you guys living in my basement?

no problem

  • Customer: David from Mayfield KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
put door catch in hole

Scraping noise from front of dryer

  • Customer: DAVID from DOVER NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I had this happen a couple years ago so I knew what to do. The hardest part is getting the old glue off. I did that with some nail polish remover and a paint scraper - probably took 20 minutes just to get the glue off. From there, it's just glue on the new one and slap it back together. In hindsight, however, I would've ordered and installed the lower guide as well and done it all at once.

Squeak and clothes getting stuck

  • Customer: Matthew from Alto MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just want to say what a great company to order parts from, I ordered the wrong parts by mistake, broke the part trying to install the incorrect part, emailed customer service and they not only gave me credit for the wrong part I ordered but, also for the shipping...I will definitely be ordering again from this company

Squealing after dryer running 20 m inutes

  • Customer: Charles from Flagler Beach FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Installed Upper Drum Glide. Fixed problem 90%. Sprayed silicone on pads and squeal almost all gone.

Dryer Won't Heat Up

  • Customer: Michael from Los Angeles CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Never knew I was handy, but I did it! I was reluctant to spend a couple $100 on a repair visit, so found this site and bought the coils I needed for only $26+tax. It's pretty easy. I just lifted up the top of the dryer with a screw driver, should snap open. Then unscrewed the front panel with two screws from the inside. Then located the old coils on the bottom left. The bracket that holds them is a little difficult to remove as you need to have a small philips screw driver to get the back one. But once I got that off, just unplugged the old ones and put the bracket back, then the panels and it WORKED. The only problem I have is that I didn't take the door switch off properly and now the dryer doesn't stop spinning if I open the door and want to check the clothes. So I may have to get someone in eventually.

Removing old felt and glue

  • Customer: Gerald from Battle Creek MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After removing the old drum glide there was tufts of felt and glue left behind. The DIY video (which inspired me to try this repair myself) says to use a scraper and wire brush to clean the drum edge. I decided to try a drill with a wire wheel. Worked great. The surface was shining clean in minutes.

dryer would heat up but shut off too early

  • Customer: D from Oak Park IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
pushed screwdriver into the two clips between the top and front to release the connection. took off front. at the bottom front left side, took out screws to access parts that needed to be replaced. put everything back together. dryer works like new. easy.

Lint screen torn

  • Customer: Debra from York PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the lint screen, got a screw driver, removed two screws for the lint screen frame, installed the new frame, BAM done. One of the easyist repairs I made.

clothes getting stuck in drum and leaving brown marks on them

  • Customer: Tony from Ukiah CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I want to suggest that you also purchase the lower drum seal or guide as well. When I took it apart I realized I needed it also.

dryer wouldn't heat

  • Customer: robert from sonora CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Part Select got me the right parts in the agreed time--good job. Shut off the power or unplug the dryer which ever is easiest. The toughest part of doing this job was figuring out how the lid came off the dryer, if you have a jack knife or a putty knife you push it in between the top of the dryer and the body about an inch below the dryer top and about six inch from both sides of the dryer front you will hit a latch that releases the top--slip a screw driver into the opening and do the other side. The top can be removed or you can hold it open with a stick. There are two screws that you need to locate they are on the inside of the dryer front about 9" from the top one on each side they are all that hold the front on the body so remove them but carefully not to drop them inside the dryer. On my dryer there were two screw inside the dryer door that held the filter body onto the front that had to be removed too. Then push the screw driver between the front and the body of the dryer like the top and it will pop open. There are some wires going to the front from the body they can be unplug just follow the wires to the connection point. On mine, I squeezed the sides of the connector and the wires pulled apart. Now you can move the front aside. At the lower right in the body you find the valve and heater burner. On top of the valve there are two sets of wires coming off the valve. Disconnect the wires--one set is for a three wire connection the other for two wire connection. Your parts have a two wire coil and a three wire coil. The coils are freed by unscrewing the metal cover that holds them down remove the two screws and that cover then remove the old coil off the valve then replace the new coil with the part that is the same. Three pin coil with three pin coil positioning in the same way as the old coil, then do the other one. Reattached the metal cover with the screws and put it all back together in reverse order. The dryer chamber--the inside of the dryer rests on the front so when you put them together you may have to lift the chamber up to met the face a little (1/4"). Good luck.
All Instructions for the TDG336RBW1
196-210 of 241