Models > TDG336RBD0

TDG336RBD0 Tappan Dryer - Overview

Get Parts and Repair Help for TDG336RBD0

If you know the dryer repair part you need, you can browse the list of all parts on the TDG336RBD0, or you can search by name or part description. You can also find your part by where it is located on the TDG336RBD0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for TDG336RBD0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$31.11

Rear Drum Bearing Kit

This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant and installation screws.

Order within the next 1 hr and 20 mins and your part ships today!
$7.61

Drum Belt

This 87-3/4" long dryer drum belt goes around the dryer drum and the pulley to rotate the drum once motor is activated.

Order within the next 1 hr and 20 mins and your part ships today!
$18.16

Upper Drum Glide

Front upper felt glide pad with 3 nylon glides - includes adhesive.

Order within the next 1 hr and 20 mins and your part ships today!
$2.83

Drum Support Bearing

Order within the next 1 hr and 20 mins and your part ships today!
$25.18

Door Catch

Order within the next 1 hr and 20 mins and your part ships today!
$17.62

'M' Series Ignition Coil Kit

This ignition coil kit contains two coils. One is a two wire secondary coil, while the other is a three wire booster coil. Both should be used together in your gas clothes dryer.

Order within the next 1 hr and 20 mins and your part ships today!
$7.32

Door Strike

"Male" piece of a dryer door closing mechanism.

Order within the next 1 hr and 20 mins and your part ships today!
$8.70

Bearing Bracket

Order within the next 1 hr and 20 mins and your part ships today!
$27.67

Flame Sensor

This part senses the flame for heat allowing the gas valve to open.

Order within the next 1 hr and 20 mins and your part ships today!
$9.82

Idler Pulley Assembly

Use this idler pulley assembly with gas or electric clothes dryer that has a flat dryer belt. ***Please NOTE: This part has been redesigned by the manufacturer and may not fit your appliance.

Order within the next 1 hr and 20 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Squealing noise

  • Customer: Cynthia from Lexington SC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Wrench set, Wrench(Adjustable)
  • 398 of 402 people found this instruction helpful
We followed the instructions for the drum glide replacement and changed the belt and drum support bearing piece, cleaned it out too. Works like a charm. Thanks for saving us a bundle. read more

Loud Squeaking

  • Customer: Frank from Boyertown PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 254 of 262 people found this instruction helpful
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Acc... read more

Drum glide wore down and caused close to get stuck between drum and front panel.

  • Customer: William from Boise ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 165 of 230 people found this instruction helpful
Unpluged dryer. Removed the top of dryer by pushing in a retaining clip on both sides of the front lip with a screw driver. Remove the two screws on both sides of front panel. These screws are square head or phillips #2. Unplugged the wiring harness to front panel (make sure power has been disconnected). Support drum and lean front panel away from dryer ... read more