Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TDB210RFS2 > Instructions

TDB210RFS2 Tappan Dishwasher - Instructions

All installation instructions for TDB210RFS2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TDB210RFS2
61-75 of 305
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishwasher leaked sometimes depending on how I loaded it.

  • Customer: Raymond from San Jose, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.

Spray Arm popped of during cycle and melted

  • Customer: Lisa from El Paso, AR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
Found your website, red the reviews, followed the simple instructions provided by others that had had the same problem and repair was complete in less than a minute. No tools needed. I am a handy girl and tackle a lot of repairs/projects, this is the first time that the job was actually easier than stated. Thanks for providing a good porduct, at a decent price WITH LAYMAN INSTRUCTIONS!!!

Wheels on lower rack melted

  • Customer: Jason from Lafayette, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.

Noisy, vibrating pump

  • Customer: Marshall from Beaverton, OR
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 5 of 7 people found this instruction helpful
After moving the dishwasher out from the cabinetry, I removed the screws holding the pump in place. Pulling the pump from the formed plastic opening, I found a toothpick lodged in the pump housing. At the same time I noticed that the front o-ring was deformed due to being the incorrect size (too large). It was installed at the factory this way.

I went online to search for new parts. PartSelect was the second or third listing on the search page. I submitted the dishwasher model number and was taken to a set of parts illustrations. I was easily able to find the o-rings I needed.

Strike plate on dishwasher broke.

  • Customer: Phillip from Wellington, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
Removed damaged strike plate from dishwasher and screwed new part into place. Tested and dishwasher worked fine. Took less than 15 minutes to get the job done. Was very pleased with how fast the part was delivered.

Dishwasher not cleaning dishes, found it not filling with water because hose was ruptured

  • Customer: Jimmie from Houston, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Turned off elecrtic and water to dishwasher and pulled dishwasher out from under cabinet. Removed broken hose using pliers to open hose clamps.
installed new hose.

dish washer would not drain.

  • Customer: Wayne from Providence, RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
I pulled out the internal filter and assorted washer parts. All in good shape. I bailed out the washer and removed the pump assembly from under the washer. I pulled it apart to inspect impeller. all looked fine. Plugged pump in and turned on pump cycle. Pump did not operate as it should have and I ordered new pump. My daughter put it back together and all is working well now!

no water entering the dishwasher

  • Customer: Douglas from Lakewood, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 5 of 8 people found this instruction helpful
turned off electricity, pulled dishwasher out about a foot, turned off water too dishwasher, removed inlet valve and replaced it with new.

Leaking Dishwasher

  • Customer: Andre from La Mirada, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.

Dishwasher door strike piece broke. Door had to be propped closed each time dishwasher was used.

  • Customer: Charles from Fort Washington, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 6 people found this instruction helpful
Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!

Dishwasher was leaking

  • Customer: Tony from Lavallette, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 3 of 3 people found this instruction helpful
I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!

Leaking dishwasher door

  • Customer: Larry from Signal Mountain, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!

Dishwasher was leaking at the front, just below the door

  • Customer: Jim from Woodburn, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

The relatively new Frigidaire (Electrolux) dishwasher would not drain the water out of the base of the washer. The pump impeller assembly was making a "rattling" sound and wasn't pumping

  • Customer: Robert from Shoreview, MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
I ordered the replacement pump from Partselect and it arrived 3 days later. The new pump went in very simply with two mounting screws (don't over tighten!!) and the two hose claps for intake and discharge. It works perfectly!

Dishwasher was leaking out of door seal. Sent PartSelect the brand and model number of the dishwasher and they did the rest. The replacement part was exactly the same as the old part. Delivery was fast and efficient. Only took a few minutes to replace and the dishwasher is back in running condition

  • Customer: Everett from Bridgeton, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.
All Instructions for the TDB210RFS2
61-75 of 305