TC607S0 Jenn-Air Trash Compactor - Instructions

The online repair states the repair could be done in 10-15 minutes and actually took over an hour. It would have taken 10 minutes if I could have just purchased the metal flange that broke.

The part was suppose to come with instructions, but did not. However, it was easy after reading the comments on-line, and discovering that the front cover had to be removed in order to expose the whole switch and wires. I did drop one of the mounting screws down the front of the compactor and was not able to recover it. So, I had to make a trip to the hardware store for a replacement. They couldn't match the remaining screw but I found 2 similar ones with lock washers and nuts that worked just fine. I saved a $90 service charge and probably double the cost of the switch by doing it myself.

I installed the new bracket, however not the new switch that came with the kit as the old switch was fine. The one key which threw me for several hours is, you must replace the switch, located in the compactor. The new switch is normally open when compressed, the old switch is closed when compressed.

Follow the included instructions carefully (read it all through first) and this was a quick and simple fix if you are reasonably handy with a screwdriver and drill. It took me about 45 mins. You have to pull the unit out from under the countertop and then remove a series of small screws in order to get behind the front panel. Putting in the new actuator switch was a little cumbersome simply because there are other wires you have to work around but it's still very straightforward. After you reinstall the front panel, you attach a new foot activated button that presses down on the new actuator switch. You have to drill 2 small holes in the front panel sheet metal to attach this new button but a perfectly sized paper template is provided and it worked great. Last easy step is to replace the rubber door sweep so that the new button can be accessed with your toe. In effect, the compactor is now operated by pressing your toe against the new button on the lower right side below the door. It is a nice improvement over the old method of lifting up on the lever that you normally step on to open the door. Easy to install.

Thanks to Parts Select and their detailed instructions it turn out great! Replacement Parts fit Great!

bought new gears, pulled it out and replaced the gears. wasn't very hard. I did expect a jenn-air to be better built (plastic gears really!) but for 30 bucks it is all better.

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

This replacement kit did solve the problem but required replacement of a number of parts because the switch and actuator functionality had been redesigned. Fitting the kit of parts requires that you have to slide the compactor away and out of its location (might be a bit tricky if it's beautifully integrated into a designer kitchen)so as to remove the front cover. Some heavy leather gloves could be helpful here since there are several sharp edges on the pressed steel carcase of the unit. Once free the kit replacement is relatively easy (for the average handyman/woman), following the simple instructions provided. You will need to drill two new holes in the front plate (template provided) so an electric drill and a sharp drill bit (for metal) will be needed. Most important - the kit worked; and with a more reliable component than that replaced.

Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.

It was an updated revision part kit...and it went so smooth ....recommend that anyone looking to repair appliances utilize PartSelect....I know I will be ...Thank You

Went well but took time. Instructions adequate but not detailed.

replaced the large gear and put it back together.

took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together

The instructions were pretty straight forward. I did not expect to receive the foot pedal and switch as mine was still ok. However, I find that everything works with less effort than before. I did have to trim the new toe guard as it hit the actuator button when opening and closing the compactor.

After removing the compactor from under the counter, and unplugging it, I did the disassembly. The replacement parts were easy to install. Two holes had to be drilled to mount the switch, but that was not difficult. Overall, the instructions were easy to follow and the parts all fit.