Models > TC407B > Instructions

TC407B Jenn-Air Trash Compactor - Instructions

All installation instructions for TC407B parts

These instructions have been submitted by other PartSelect customers and can help guide you through the trash compactor repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TC407B
31-45 of 70
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Plastic Drive gear broke

  • Customer: Terry from Spring TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 2 of 4 people found this instruction helpful
The plastic drive gear broke and the unit was locked in the down position. The repair kit contained all of the parts required to fix the problem plus other replacement parts for the gear drive unit. It was very easy (about 20 min.) to replace the gear and other parts. The unit works fine now.

compactor wouldn't shut off

  • Customer: Ray from Dallas GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
changed out the switch and that fixed the problem

motor gear broken

  • Customer: Clem from Scottsdale AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....

Compactor would not open. Ram was down

  • Customer: James from Flagstaff AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 1 of 2 people found this instruction helpful
Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.

Toe guard was broken, foot pedal was discolored.

  • Customer: Michael from Ashfield MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 5 people found this instruction helpful
Replaced both, results like new.

worn guard scratched door panel

  • Customer: harold from walpole MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 3 people found this instruction helpful
removed old parts and replaced

PLASTIC GEAR WHEEL BROKE

  • Customer: Reagan from Glenshaw PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 1 of 3 people found this instruction helpful
Emptied all garbage!
Laid machine on its side.
Removed cover.
Removed left over gear parts by removing pin.
Loosened chain by removing two top left corner screws.
Place new PLASTIC gear in position with chain.
Returned screws to top left corners.
Returned pin to gears.
Make sure chain is taught.
Replace cover.
Lift back up from its side.
Test.

unit was missing parts

  • Customer: Richard from glendale AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Installed new parts. Worked fine.

Compactor ram was stuck in the down position and door would not open

  • Customer: Michael from South Boston MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!

Broken Drive Gear

  • Customer: Michael from Painted Post NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 4 people found this instruction helpful
Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.

Ram quit moving

  • Customer: Hal from Granada Hills CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Removed bottom and replaced gears

roller bearing for trash bin was damaged and would not allow canister to roll

  • Customer: roberto from keller TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 1 of 11 people found this instruction helpful
the bearing were the perfect match and instructions helpful. sysem is rolling smoothly

Unit cycled when on switch operated and would not stop until Off switch was activated.

  • Customer: Gerald from Wickenburg AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Replaced the limit switch. This did not alter the problem. Took off the On/Off/Start switch and dissasembled. I found the the Start switch was stuck in the on position. I reassembled the switch mechanism assuring that the Red "ON" indicator moldings were correctly positioned and reassembled everything. The Compactor now works properly. Need to add "Check the Start switch" to diagnosis.

I changed the front panels from the original beige to stainless steel

  • Customer: Walter from San Rafael CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was a breeze, a piece of cake, a walk in the park, a day at the beach. The part arrived quickly and installation was fast and simple. A week earlier I had the misfortune of ordering these parts from another supplier. One of the parts obviously was not correct, so I called customer service. Although the operator was polite, she insisted that the part I received was the right one (even though it was 2 inches too narrow). I looked up the part at PartSelect.com and ordered it. It arrived the following day, and fit perfectly. Thanks, PartSelect.com.

Broken drive gears

  • Customer: THOMAS from DENNISPORT MA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Took out old gears replaced with new very easy with your dirictions.
All Instructions for the TC407B
31-45 of 70