Models > SXD22S2W (P1190404W W) > Instructions

SXD22S2W (P1190404W W) Amana Refrigerator - Instructions

All installation instructions for SXD22S2W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SXD22S2W
496-510 of 612
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

not made ice

  • Customer: Sunny from RICHARDSON TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The part came in 5 days from time order. take less then 10 minute done. part work well, have ices again, Thank you Part Select. we don't have to buy a new Rerigerator

Ice maker not making ice

  • Customer: Warren from Houma LA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I started by changing the water inlet valve. It made one batch but it did not eject into the ben. I removed the ice maker and found that the coating inside was bad. I changed out the ice maker and it is now making lots of ice.

Ice would not dispense

  • Customer: Gregory from Willow Park TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Reomove Ice bin from unit.remove plastic front. Remove the 2 bottom screws of dispenser assembly. removed old assembly. position new assembly. Replace bottom 2 screws.reinstall plastic front and reinstall into unit.

Not making ice

  • Customer: Raymond from Hanover Township PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I went on line and viewed the video. It looked so easy I ordered the new ice maker. Having the information I was able to take apart the old one and view the problem. By the time the new part arrived I was experienced with the installation. I was shocked when the new ice maker arrived within 1 day. I completed the installation without a hitch, I was delighted with the ease of installation and the operation of the new iace maker.Thanks again...Ray

Ice maker quit

  • Customer: Peter from Johannesburg MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed contents of freezer as this was a bottom unit. I had to remove freezer drawers/door to easily access ice maker which was located in the back of unit,wasnt a problem.I did however take a hair dryer to water tube as it froze up with about an 6 inch tube of ice that finally slid down. Connected unit and had ice within an hour or so and a full tray within 24 hrs. Second ice maker in little over a year...Video very helpful, saved 100 bucks by doing myself. Part arrived fast, great job!

Ice maker leaked a little, then quit completely.

  • Customer: Steve from Lansing MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We ordered a PartSelect PS2121513 ice maker. I was concerned that there was no instructions shipped with the unit. Fortunately, PartSelect had an online video that guided me through the process. It wasn't that complex really. The only time I felt totally dumb was when using my nut driver to remove the bottom bracket. I couldn't figure out why there was no 1/4" socket with my set, so I used a small socket wrench instead. I finally figured out that the driver was already a 1/4", without a socket in it. After that it was easy. Slid the ice maker up a little to free it from the top mounting screws. Pulled it outward a bit to gain access to the connector at the back of the freezer, then squeezed the two sides of the connector and out it came. I popped the plastic cover off the existing device and then removed the connector as instructed in the video. I also removed the bale (as per the video). I put the connector harness, plastic cover and bale on the new ice maker and put it back in, this time using the nut driver on the bottom bracket :-). My only concern after that was that it didn't seem to be working. I had no idea that it needed some time to get cold before it would work. After about an hour, it filled with water and began making ice. Success.

The ice maker was not making ice

  • Customer: Brian from Lakewood CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Turned off the water supply line. Unplugged electrical outlet. Removed the lower back panel cover. Disconnected the water suppy line. Removed two 1/4 inch screws from water inlet valve mounting bracket. Disconnected the two plastic water lines by unscrewing the plastic nuts. Disconnected two electrical connections. Removed old water inlet valve from mounting bracket. Replaced and connected all parts and connections in reverse order.

Musty taste to water from refridgerator water dispenser.

  • Customer: Edward from Washington MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced cold water dispenser reservoir. Removed back access panel on bottom of refridgerator. Cut hoses using a wire cutter and removed old reservoir. Installed new unit (one screw). Routed hoses through bottom of refridgerator. Cut length to allow hose splicing just beneath resevoir. Connected hoses using hose splicers provided with the part. Musty taste is better if a couple glasses of water are run through the unit before drinking each time. Previously the water never got better. I think more hoses need to be replaced in the door to fully solve the problem. Repair took less than 30 minutes.

Ice maker stopped working. Turned out a connection on the heating bar shorted out.

  • Customer: Russ from Supply NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pulled the plug on the refrig. ( This is important since the heating bar on the bottom of the ice maker could come on as soon as you plug it in and burn your hand ). Removed the ice bin to get it out of the way and then removed the 1/4" hex screw from the support bracket under the old ice maker ( don't lose it ). Pushed up on the old ice maker to dislodge it from the 2 support clips on the top of the ice maker. Squeezed both sides of the wire harness plug and pulled it out and removed the old ice maker. Removed the wire harness and level bar from the old ice maker and installed them on the new ice maker. Plugged the ice maker wire harness into the female receptacle in the freezer. Popped the ice maker in to the top support clips making sure the rubber water chute from the refrig. was in place in the round ice maker receptacle. Plugged bak in the refrig. and I was getting ice in about 2 hours. Working fine after 1 week producing plenty of ice. RussK---

Fan motor stopped working

  • Customer: john from white pine TN
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Well I could what laid on the floor and replaced it but I didn't I emptied refrigerator laid it over change the motor then stood it back up actual work about three hours

ice maker stopped making ice

  • Customer: David from Jacksonville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
following the advice of this site, purchased a new ice maker. Old one was simple to unhook and remove and new one was just as easy to install. Within no time at all, I had ice being made and it has been working perfect since. Thank you for the help...

slow water flow icemaker was making hollow ice cubes

  • Customer: Gary from Butte MT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
I removed the bottom fabric type panel on the back of my refrigerator.The copper supply tube leads to the water inlet valve. Turned off water supply to the refrigerator and dis-connected the water supply tube (copper line)that hooks to the inlet valve. Removed two screws holding the inlet valve bracket to the refrigerator frame. I then pulled the whole unit back a couploe inches and then dis-connected two wires with quick type connections and another ground wire from the bracket. I then unscrewed two water supply tubes(plastic) that go under the refrigerator. These tubes supply water to the refrigerator and icemaker. I then pulled the valve assembly from the bracket and then reconnected the new valve/s in reverse order. After turning on the water I used the water dispensor on the refrigerator door to fill and empty several glasses to get rid of any contamination in the water lines. Very quickly I had a really strong water supply for the water dispensor and solid ice cubes. After a couple weeks however the ice cube maker stuck open and flooded my kitchen, so if you do this watch for problems for awhile and shut off the water supply if you go on vacation. This job was pretty easy and I wouldn't be afraid to try it. Gary

Ice Maker was not functioning

  • Customer: BRET from SAN DIEGO CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed your posted video. Did step by step as video instructed and in about 30 minutes finished. Ice was made approx 30 minutes later. I hope you do more videos, a picture is worth a thousand words.

Ice cubes would not dispense out of the door

  • Customer: Joseph from San Marcos CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replace the Auger & Crusher blade. Very easy to do and it works great now. Also, your customer service was great!! shipped the same day and arrived to me the next day!!

Refrigerator not shutting off, liquids freezing in fridge

  • Customer: Barbara from Apollo PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It wasn't quite as easy to get to the bolts as the video showed. The lay out of the part wasn't exactly like the video either. However, I managed to put the new part in. Unfortunately, it didn't solve the problem. At first the fridge cycled on and off but after 12 hrs it started to freeze liquids again. Since the appliance was 17 years old we opted to just get a new one.
All Instructions for the SXD22S2W
496-510 of 612