Models > SWXG831HS1

SWXG831HS1 Westinghouse Washer / Dryer Combo - Overview

Get Parts and Repair Help for SWXG831HS1

If you know the washer / dryer combo repair part you need, you can browse the list of all parts on the SWXG831HS1, or you can search by name or part description. You can also find your part by where it is located on the SWXG831HS1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer / dryer combo. We’ve also included any installation videos we have for SWXG831HS1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$19.45

Drum Glide

Sold individually. 2 are required.

$2.77

Drum Support Bearing

$12.46

Drive V-Belt

This belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

$13.81

Lower Front Felt Seal with Adhesive

$23.71

Door Catch

$19.41

Lint Filter

This filter collects lint as it passes through the dryer vent.

$10.26

Multi-Rib Drum Belt

$100.34

Drain Pump - 60Hz 120v

The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.

$18.46

Water Inlet Valve

This washing machine water inlet valve has two ports for water to enter.

$22.77

'M' Series Ignition Coil Kit

This ignition coil kit contains two coils. One is a two wire secondary coil, while the other is a three wire booster coil. Both should be used together in your gas clothes dryer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replace broken drive belt

  • Customer: rodney from fairfield bay AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 120 of 137 people found this instruction helpful
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run... read more

would't spin all water out or rinse out clothes

  • Customer: kenneth from willard OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 72 of 86 people found this instruction helpful
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes l... read more

squeeking like crazy

  • Customer: Steve from Wheelersburg OH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 51 of 57 people found this instruction helpful
well, i started at the top and worked my way down. by taking the top off, it gave me more room to get the dryer tub out. took the two screw`s out of the vented plate on the back of the machine to undo the belt. this is a stackable washer-dryer combo, so next i took off the white plate on front between washer & dryer. took off the control panel, unpluged it, ... read more