Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SWXG831DS0 > Parts

SWXG831DS0 Westinghouse Washer Dryer Combo - Parts

All parts for the Westinghouse Washer Dryer Combo SWXG831DS0

Below is a list of all parts for the Westinghouse Washer Dryer Combo SWXG831DS0 - White. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the SWXG831DS0
1-14 of 199
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$20.80

Drum Glide - White

This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there a...

$2.41

Drum Support Bearing

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which attaches onto the inside of the rear panel of the cabinet. You will need to remove the dryer drum before completing this repair. Although replacing the drum support bearing is a fairly easy job, you will need tools to complete it. For this repair, you will need a putty knife, a Phillips screw driver, a 5/16 nut driver and maybe a small flat blade screw driver.

$13.55

Drive V-Belt

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer,...

$20.56

Lint Filter

This lint filter is used in dryers. It works to collect lint and debris when it passes through the dryer vent. Air flow is necessary for the dryer to function properly and consistently, therefore it is crucial to clean your filter before every load. If your filter has tears, rips, or your clothes take too long to dry, make sure to replace this part to resolve these problems. As a safety precaution, remember to unplug the dryer from the power source and wear work gloves before beginning this installation.

$8.90

Multi-Rib Drum Belt

The multi-rib drum belt is also known as a drive belt and is a part for your dryer. The function of the drum belt is to attach to the motor pulley. It will then spin the drum as th...

$13.16

Lower Front Felt Seal with Adhesive

$28.01

Door Catch

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, w...

$14.16

'M' Series Ignition Coil Kit

This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the symptoms that this kit could be a solution for are: If there is no heat, not enough heat, or clothes takes too long to dry. In this case, the gas valve coils can be defective and replacing this part will help. Customers rate this project as easy. Refer to the installation diagram for further instructions. For safety, unplug your dryer before repair.

$5.42

Screw-In Plastic Leveling Leg

Sold individually.

$99.81

Drain Pump - 120V 60 Hz

This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.

$18.91

Water Inlet Valve

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the...

$14.48

Front Upper Felt Seal with Adhesive

$45.48

Ball Hitch

This ball hitch provides support to the drum located at the back wall of the dryer. This allows the drum to spin. The bearing may have gone bad and you might notice that the ball i...

$10.33

Bearing Bracket

This OEM drum bearing bracket holds and supports the drum bearing in your clothes dryer. The bracket is located behind the dryer drum. Common symptoms that are linked to faulty or damaged drum bearing brackets include: the dryer will not start, will not tumble, or the dryer is making loud squeaking or grinding sounds. If there is an issue with the bearing bracket, it will need to be replaced. Replacing the bracket has been listed as a very easy to easy repair by many of our customers. Remember to disconnect the power to your dryer before beginning this repair.

All Parts for the SWXG831DS0
1-14 of 199