Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SWSG1031HS2 > Parts

SWSG1031HS2 Westinghouse Washer Dryer Combo - Parts

All parts for the Westinghouse Washer Dryer Combo SWSG1031HS2

Below is a list of all parts for the Westinghouse Washer Dryer Combo SWSG1031HS2. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the SWSG1031HS2
1-14 of 196
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$20.80

Drum Glide - White

This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there a...

$2.41

Drum Support Bearing

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which attaches onto the inside of the rear panel of the cabinet. You will need to remove the dryer drum before completing this repair. Although replacing the drum support bearing is a fairly easy job, you will need tools to complete it. For this repair, you will need a putty knife, a Phillips screw driver, a 5/16 nut driver and maybe a small flat blade screw driver.

$13.55

Drive V-Belt

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer,...

$20.56

Lint Filter

This lint filter is used in dryers. It works to collect lint and debris when it passes through the dryer vent. Air flow is necessary for the dryer to function properly and consistently, therefore it is crucial to clean your filter before every load. If your filter has tears, rips, or your clothes take too long to dry, make sure to replace this part to resolve these problems. As a safety precaution, remember to unplug the dryer from the power source and wear work gloves before beginning this installation.

$9.38

Thermal Limiter - Limit 220

The dryer thermal limiter, also known as a thermal fuse, blows the fuse to cut off power to the dryer when the dryer begins to overheat. Once the dryer reached 220 degrees Fahrenhe...

$8.90

Multi-Rib Drum Belt

The multi-rib drum belt is also known as a drive belt and is a part for your dryer. The function of the drum belt is to attach to the motor pulley. It will then spin the drum as the motor rotates. Over time this part will naturally dry out. If your drum belt begins to crack or break, the dryer will not be able to continue to turn. If your dryer is running but your belt will not rotate, that likely means that it has been damaged and needs replacing. The tools you will need for this repair are a putty knife and a screwdriver set.

$8.63

Knob

This knob includes tension spring clip and will accept a D-shaped shaft. Sold individually.

$13.16

Lower Front Felt Seal with Adhesive

The lower front felt seal with adhesive, also known as a drum felt seal, is used in dyers and allows the drum to easily glide on the front panel. For this repair project, you will need the following tools: #2 Phillips screw driver, #2 square head screw driver, putty knife, and wire bush. If your dryer will not tumble, or makes a squeaking noise when running, replacing this part could solve the problem. Remember to unplug your appliance from the power source for safety before you begin this installation project. Refer to the manual provided by the manufacturer for further installation instructions.

$28.49

Door Catch

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, w...

$14.16

'M' Series Ignition Coil Kit

This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the symptoms that this kit could be a solution for are: If there is no heat, not enough heat, or clothes takes too long to dry. In this case, the gas valve coils can be defective and replacing this part will help. Customers rate this project as easy. Refer to the installation diagram for further instructions. For safety, unplug your dryer before repair.

$99.81

Drain Pump - 120V 60 Hz

This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, whi...

$14.48

Front Upper Felt Seal with Adhesive

$5.56

Screw-In Plastic Leveling Leg

This is a screw in leveling leg for your washing machine. It supports the appliance by screwing in place to create a stable and flat surface. Take note that you are able to adjust ...

$18.91

Water Inlet Valve

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve is in any way damaged or defective, it may be slow to fill or even leak. Before beginning this replacement, make sure to unplug the washer from the power range or shut off the house circuit breaker. Remember to wear gloves for safety. Refer to the installation instructions and the diagram provided by the manufacturer for best results and accuracy.

All Parts for the SWSG1031HS2
1-14 of 196