Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SWSG1031DS1 > Parts

SWSG1031DS1 Westinghouse Washer Dryer Combo - Parts

All parts for the Westinghouse Washer Dryer Combo SWSG1031DS1

Below is a list of all parts for the Westinghouse Washer Dryer Combo SWSG1031DS1 - White. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the SWSG1031DS1
1-14 of 196
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$20.80

Drum Glide - White

This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there a...

$2.41

Drum Support Bearing

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which attaches onto the inside of the rear panel of the cabinet. You will need to remove the dryer drum before completing this repair. Although replacing the drum support bearing is a fairly easy job, you will need tools to complete it. For this repair, you will need a putty knife, a Phillips screw driver, a 5/16 nut driver and maybe a small flat blade screw driver.

$13.55

Drive V-Belt

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer,...

$20.56

Lint Filter

This lint filter is used in dryers. It works to collect lint and debris when it passes through the dryer vent. Air flow is necessary for the dryer to function properly and consistently, therefore it is crucial to clean your filter before every load. If your filter has tears, rips, or your clothes take too long to dry, make sure to replace this part to resolve these problems. As a safety precaution, remember to unplug the dryer from the power source and wear work gloves before beginning this installation.

$8.90

Multi-Rib Drum Belt

The multi-rib drum belt is also known as a drive belt and is a part for your dryer. The function of the drum belt is to attach to the motor pulley. It will then spin the drum as th...

$8.63

Knob

This knob includes tension spring clip and will accept a D-shaped shaft. Sold individually.

$13.16

Lower Front Felt Seal with Adhesive

$28.01

Door Catch

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door to stay secure. Before you begin this repair make sure to disconnect the power supply to the dryer. The tools you will need for this installation include a Phillips screwdriver and a small flat blade screwdriver. A pair of pliers may also come in handy. Users ranked this repair as easy, and say that it will take fifteen minutes or less to complete.

$14.16

'M' Series Ignition Coil Kit

This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes...

$5.42

Screw-In Plastic Leveling Leg

Sold individually.

$99.81

Drain Pump - 120V 60 Hz

This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, whi...

$18.91

Water Inlet Valve

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve is in any way damaged or defective, it may be slow to fill or even leak. Before beginning this replacement, make sure to unplug the washer from the power range or shut off the house circuit breaker. Remember to wear gloves for safety. Refer to the installation instructions and the diagram provided by the manufacturer for best results and accuracy.

$14.48

Front Upper Felt Seal with Adhesive

$45.48

Ball Hitch

This ball hitch provides support to the drum located at the back wall of the dryer. This allows the drum to spin. The bearing may have gone bad and you might notice that the ball is cut off. The ball hitch might need to be replaced if you notice that your dryer is extra noisy, is not tumbling properly, or will not start at all. The ball hitch is made of metal and measures 5 inches in diameter. This is an OEM part that is sourced directly from the manufacturer.

All Parts for the SWSG1031DS1
1-14 of 196