Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SWS933AQ0 > Instructions

SWS933AQ0 Westinghouse Washer - Instructions

All installation instructions for SWS933AQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SWS933AQ0
61-75 of 147
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

missing cup for fabric softener

  • Customer: Les from Alpena, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Pulled it off and just replaced it

water leaking from bottom hose

  • Customer: James from Brandon, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 2 of 3 people found this instruction helpful
remove one hose clamp.pulled hose from back of washer.replaced with new hose in same procedure.best of all i had my new hose in two days.great serviceand inventory.

over fill caused door to come open

  • Customer: Bill from Unionville, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
removed top cover to access valve dissconnected hoses and wires then unscrewed valve and replaced

Washer would only let cold water in,then not fully cycle

  • Customer: George from Ketchikan, AK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Disconnect power,take water hoses off using pliers,they are really tight,remove 2 philips head screws,pull 2 wire connectors off and water fill hose squeezing wire clamp and sliding clamp back on hose.reverse to install.Works like a champ.

Inlet valve leaked water from supply line(s) back into washer.

  • Customer: John from Powhatan, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
Pulled washer electrical plug from receptacle.
Unscrewed hot and cold water inlet hose connectors.
Removed screws retaining backplate.
Removed back plate.
Removed two screws connecting valve assembly to frame.
Pulled two spade electrical wire connectors from valve assembly.
Opened hose clip securing hose on outlet side of valve assembly, using pliers.
Pulled hose from valve assembly.
Valve assembly now free.
Reversed above with replacement valve assembly.

burning rubber smell

  • Customer: Lewis from Thornton, CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Poped up top, removed front pannel (2 phillip head screws) observed failed belt. Replaced belt. Tensioner can be held back by hand so it was easy. Works great. Part Select Rocks! I put in the model number and bam, there was my needed part, 3 days later it was in my hands. This was after me wasting time driving around town trying to find it at home depot type stores to no avail. I'll never do that again. This website makes repairing appliances a snap. Gotta love on-line shopping! woo hoo

Discharge hose was leaking

  • Customer: John from Hyattsville, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
This is a newer washer, but I don't know the age. I just bought the house...!

I made this repair more difficult than it needed to be. I took off the back panel of the machine completely, only to discover the coupling for the hose was near the front of the machine. I tilted the unit on its side and took off the bottom before I discovered the access panel on the front, which is held on by only two screws. I put the bottom panel back on, tilted it upright, took off the panel, and had easy access to the coupling. The new part fit perfectly, and a quick wash load proved the leak was fixed.

drive belt old and stretched

  • Customer: George from Sault Ste. Marie, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
unplugged machine. pried up with large regular screwdiver on top washer lid. removed two phillips screws bottom of front panel, had to use rubber mallet to drive front panel down to remove as was rusty and old. removed old belt using screwdriver. put new belt under tub pulley and put belt on small pulleys. kept moving tub and springs by pushing on tub. Took several tries to get new belt to go on the large tub pulley but finally did it. I used the instructions you gave for replacing broken drive belt and it worked. replaced front panel and two phillips screws, put top back on and away it went.

Washer Not Draining

  • Customer: Craig from Asheville, NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
After not being able to get the proper 10 foot hose, and having to splice two drain hoses together....turned out it was not the drain hose after all, but the pump. Some sort of "baffle" in the drain hose, where the rubber connector at the pump end and the corrugated hose joins, was blocking the water I thought. It may have been since a spliced the new hose in at that end. However, I think it was the pump.

Leveling Leg Broken

  • Customer: Brian from Rochester, NH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench (Adjustable)
  • 1 of 2 people found this instruction helpful
The leveling legs on my Frigidaire stackable washer & dryer were broken. They are made of plastic and while moving the unit one of the legs had broke off. I ordered two replacements from PartSelect and received them within a few days. The old legs were removed by screwing them out and then the new ones were installed. Pretty easy installation for DIY. The new legs work great.

hot water kept filling the tank

  • Customer: Bob from Birdsboro, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL

the drain hose was leaking

  • Customer: STEVEN from HAMPTON, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 1 of 2 people found this instruction helpful
i took the hose of and stuck the water hose in it and saw a lin hole leak. i order a new hose and recived it very fast (1 day) took 15 min to put it on the pump and to put the machine back togther

Bottom "Screw", which is the front leg of the washer was broken.

  • Customer: Linda Lahann from Freehold, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 2 of 5 people found this instruction helpful
Tilted the clothes washer back to provide easy access. Then after scrubbing the floor - which took most of the time of the repair, screwed out the broken leg and screwed in the new leg or SCREW. Easy peasey.

water over flowing, old valve stuck open.

  • Customer: william from mayfield, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.

broken belt

  • Customer: odell from Elizabethtown, KY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I took off the front panel of the washer and placed the belt on the large tub wheel and then the smaller wheel. I placed the belt over the adjustable third wheel and turned the tub in order to get the belt all the way in the grooves. Thirty minutes max to replace. Thanks, my order was 100% satisfactory
All Instructions for the SWS933AQ0
61-75 of 147