SWS1233HS0 Westinghouse Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
knob broke
-
mark from sun city, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken selector knob
-
CLARK from JUNEAU, AK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
selector knob would not turn on tne dryer
i took the old knob off and put the new one on. it took about 10 seconds. it was simple.the service dept. was extremely helpful in getting the right knob. it was delivered the very next day. i would definitly recommend this company to anyone who has a parts problem.....
Parts Used:
-
diane from arlington hts., IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Selector knob broke
Took the old one off & put the new one on!!! About a 2 minute job!!!
Part arrived the day after it was ordered. Amazing service.
Part arrived the day after it was ordered. Amazing service.
Parts Used:
-
Ted from Plattsburg, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My Dryer Knob Cracked and would not turn.
I received the Dryer knob in the mail the next day. All I had to do was slip it on. Very easy installation.
Parts Used:
-
kimberleigh from Beecher, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knobs Do Not Fit Securely
Took broken knobs off and replaced with new ones. Only one fit snuggly; the other two are raised and wobbly.
Parts Used:
-
Marie from Marlboro, NY
-
Difficulty Level:Difficult
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken start knob on dryer
-
Susan from Isle of palms, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Selector knob broke
-
Prince from Murfreesboro, TN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken and worn out knobs
was just a pop off -pop on knob replacement for worn/broken knobs. Easy on ,less than a minute. The BEST part of my repair...finding exactly the parts I needed and fast shipping, also the site for selecting your parts and trouble shooting repairs is extremly customer friendly......highly reoommend your site/services. Thanks
Parts Used:
-
Patsy from Wytheville, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor burnt out
my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!
Parts Used:
-
ANNA from STATEN ISLAND, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
2 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knob on Dryer broke
I ordered the part one day & it arrived the next day(UPS-Ground)I replaced broken knob with new one & everythings just fine. Thank you for your prompt service !!
Parts Used:
-
Robert from Clearwater, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water not turning off
Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.
Parts Used:
-
Anita from Orange, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No hot water in machine
First I removed the hot and cold water supply lines to the machine. Then I removed the two screws at the top of the back panel, and pulled the entire top of the machine off which was a little tricky to figure out. There are two tension-like clips in the front of the machine holding the top on. (I had thought the back panel would come off so I was surprised when it became clear that the top of the machine would come off.) Then I unscrewed the two screws that hold the water inlet valve. I had to remove the green grounding wire that was clipped on the frame. The water inlet valve then lifted out easily. There were two clips to slide off, and a hose going into the tub that also had to come off which I did by loosening a little clamp on the end of the hose- saved the clamp for the new valve! Re-attaching everything was a snap. Tested the hot water before re-setting the top of the machine back together and it worked!
Parts Used:
-
julie from minneapolis, MN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Wrench (Adjustable)
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water would not shut off causing door to pop open and spill all over the floor
The repair would have gone much easier if I did not have a stack dryer on top of the washer. Had to roll out the total unit and work with the dryer partly on top. Only needed minimal work and tools after that.
Parts Used:
-
Joe from Interlaken, NY
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front load washer continued to fill with water until door failed. Major Flood
Removed screws at back securing top panel (4).
Removed screws holding water inlet valve to back of machine (2)
Removed water hoses to bucket
Removed squeeze clamp securing water distribution hose from inlet valve
Reversed method with new valve.
Very fast...~25 min
Works fine so far!
Removed screws holding water inlet valve to back of machine (2)
Removed water hoses to bucket
Removed squeeze clamp securing water distribution hose from inlet valve
Reversed method with new valve.
Very fast...~25 min
Works fine so far!
Parts Used:
-
Malcolm from Shelley, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!