Models > SWS1233HQ0 > Instructions

SWS1233HQ0 Westinghouse Washer - Instructions

All installation instructions for SWS1233HQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SWS1233HQ0
61-75 of 128
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer tub stopped spinning and was real noisy

  • Customer: Raymond from Brewster MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I read the last three peoples experiences when I ordered the part on your on line page. I had already made all the wrong mistakes taking the machine apart, and couldn't beleive how simplified it was on your web site. I had called a local repair shop only to be advised the part would take 4 days shipping and the price of it plus shipping was twice what I paid you. Your part arrived the day after I ordered it on line, Thanks again for being there!!!!!

The threaded male coupling on the water inlet valve is plastic and broke during moving.

  • Customer: Alan from Denver CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
I installed this part on a stackable washer-dryer unit. First, I removed the hoses (one had broken off already, damaging the cold water coupling). Using a nut driver I removed the screws on both L-brackets in back that help secure the dryer unit to the washer base. Then, I located 2 other screws securing the dryer to the washer base. These were fairly accessible in the recess where the dryer exhaust vent is located, directly above the water inlet valve. I removed both with a nut driver. I thought I would have to also unscrew 2 more screws on the other side of the dryer, but these were not accessible. So I lifted the side of the dryer I had unbolted to get to the water inlet valve. And voila! It lifted up. I placed a 2x4 on edge to keep the dryer tilted open. The inlet valve is attached to the back inside of the washer by a single screw on the Kenmore, which I removed with a phillips screw driver. Reaching inside the back of the washer, I disconnected the water hose by pinching the retaining clip with pliers. Then I pulled the electrical connections off the the hot and cold solenoids and the unit came out. The replacement unit was installed in reverse.

Inlet valve leaked water from supply line(s) back into washer.

  • Customer: John from Powhatan VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Pulled washer electrical plug from receptacle.
Unscrewed hot and cold water inlet hose connectors.
Removed screws retaining backplate.
Removed back plate.
Removed two screws connecting valve assembly to frame.
Pulled two spade electrical wire connectors from valve assembly.
Opened hose clip securing hose on outlet side of valve assembly, using pliers.
Pulled hose from valve assembly.
Valve assembly now free.
Reversed above with replacement valve assembly.

water over flowing, old valve stuck open.

  • Customer: william from mayfield NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.

water leaked into machine when turned off

  • Customer: Henry from Frenchtown NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed top,removed hose from inlet valve to washer,removed hot and cold inlet hoses and with phillips screwdriver removed water inlet valve assy and replaced. Reassembled and tested.

My order arrived 2 days after i ordered same. Excellent service from partselect, Thank You....

hot water kept filling the tank

  • Customer: Bob from Birdsboro PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL

drive belt old and stretched

  • Customer: George from Sault Ste. Marie MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
unplugged machine. pried up with large regular screwdiver on top washer lid. removed two phillips screws bottom of front panel, had to use rubber mallet to drive front panel down to remove as was rusty and old. removed old belt using screwdriver. put new belt under tub pulley and put belt on small pulleys. kept moving tub and springs by pushing on tub. Took several tries to get new belt to go on the large tub pulley but finally did it. I used the instructions you gave for replacing broken drive belt and it worked. replaced front panel and two phillips screws, put top back on and away it went.

Leveling Leg Broken

  • Customer: Brian from Rochester NH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
The leveling legs on my Frigidaire stackable washer & dryer were broken. They are made of plastic and while moving the unit one of the legs had broke off. I ordered two replacements from PartSelect and received them within a few days. The old legs were removed by screwing them out and then the new ones were installed. Pretty easy installation for DIY. The new legs work great.

broken belt

  • Customer: odell from Elizabethtown KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I took off the front panel of the washer and placed the belt on the large tub wheel and then the smaller wheel. I placed the belt over the adjustable third wheel and turned the tub in order to get the belt all the way in the grooves. Thirty minutes max to replace. Thanks, my order was 100% satisfactory

DRIVE BELT WAS NOISY-SLIPPING

  • Customer: Steve from Carrollton TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I just popped up the top front using a large straight (slotted) screw driver, then removed the 2 screws at the bottom front, then the whole front panel popped down about a half inch to be lifted out of the way. I found the old drive belt way down under the motor (still attached as normal), very near the floor and removed the worn out belt by hand, and replaced it with the new belt by hand also. The spring loaded belt tightener- idler wheel makes this a very simple process to accomplish. Then, I replaced the front panel-- all done. Works like new.

washer was not spinning

  • Customer: Mohamad from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.

I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.

water not turning off

  • Customer: Anita from Orange TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.

No cold water supply

  • Customer: Harold from Kansas City MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Removed two screws that held top of washer in place. removed top of washer. Removed two screws that held water inlet alve in place. Removed clamp and outlet hose from old inlet valve.












































































Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.

Hot water was not entering the machine, but cold water flowed smoothly

  • Customer: Ronald from Saint Louis MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 1 people found this instruction helpful
1. Turned off water to washing machine.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finished!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.

Cold water was filling slower than the hot water.

  • Customer: Steve from Fort Mohave AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Pulled out the machine. Disconnected water lines. Removed four screws attaching the top brackets. In rear of top panel. Slid top panel forward and clear of valve. Removed two wire harnesses. Removed two screws holding valve to the back panel. Pulled valve down and out. Removed outlet side line spring clamp with channel lock pliers and pulled hose off old valve. Installed outlet side hose and spring clamp onto new valve. Placed valve up into place and installed two screws. Installed two wiring harnesses. Replaced top lid. Replaced lid bracket screws. Re-attached water hoses and pushed the machine back into place.
All Instructions for the SWS1233HQ0
61-75 of 128