Models > SWS1233CS1 > Instructions

SWS1233CS1 Westinghouse Washer - Instructions

All installation instructions for SWS1233CS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SWS1233CS1
76-90 of 174
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken belt

  • Customer: odell from Elizabethtown KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I took off the front panel of the washer and placed the belt on the large tub wheel and then the smaller wheel. I placed the belt over the adjustable third wheel and turned the tub in order to get the belt all the way in the grooves. Thirty minutes max to replace. Thanks, my order was 100% satisfactory

Selector knob broke

  • Customer: Ted from Plattsburg MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Took the old one off & put the new one on!!! About a 2 minute job!!!

Part arrived the day after it was ordered. Amazing service.

Broken start knob on dryer

  • Customer: Susan from Isle of palms SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Put the knob on and done!

Selector knob broke

  • Customer: Prince from Murfreesboro TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Took it out of package..pushed it on.

DRIVE BELT WAS NOISY-SLIPPING

  • Customer: Steve from Carrollton TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I just popped up the top front using a large straight (slotted) screw driver, then removed the 2 screws at the bottom front, then the whole front panel popped down about a half inch to be lifted out of the way. I found the old drive belt way down under the motor (still attached as normal), very near the floor and removed the worn out belt by hand, and replaced it with the new belt by hand also. The spring loaded belt tightener- idler wheel makes this a very simple process to accomplish. Then, I replaced the front panel-- all done. Works like new.

KNOBS DO NOT FIT SECURELY

  • Customer: Marie from Marlboro NY
  • Difficulty: Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Took broken knobs off and replaced with new ones. Only one fit snuggly; the other two are raised and wobbly.

broken and worn out knobs

  • Customer: Patsy from Wytheville VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
was just a pop off -pop on knob replacement for worn/broken knobs. Easy on ,less than a minute. The BEST part of my repair...finding exactly the parts I needed and fast shipping, also the site for selecting your parts and trouble shooting repairs is extremly customer friendly......highly reoommend your site/services. Thanks

knob broke

  • Customer: mark from sun city AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
no problem, pushed the new knob on and all worked as it should.

water not turning off

  • Customer: Anita from Orange TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.

Dryer knob was missing

  • Customer: Carol from Millville NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Just slipped it on the on-off control, gave it a twist and it was done! Fit perfectly. So glad I found your site.

My Dryer Knob Cracked and would not turn.

  • Customer: kimberleigh from Beecher IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I received the Dryer knob in the mail the next day. All I had to do was slip it on. Very easy installation.

selector knob would not turn on tne dryer

  • Customer: diane from arlington hts. IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
i took the old knob off and put the new one on. it took about 10 seconds. it was simple.the service dept. was extremely helpful in getting the right knob. it was delivered the very next day. i would definitly recommend this company to anyone who has a parts problem.....

washer was not spinning

  • Customer: Mohamad from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.

I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.

broken selector knob

  • Customer: CLARK from JUNEAU AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
removed broken knob..pushed new knob on..

starter knob was broken

  • Customer: Sumedha from Miami Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
just slid the new knob and that was it.I have say about PartSelect.com , it was very easy to place order and next day i rec'd the part. excellent service.
All Instructions for the SWS1233CS1
76-90 of 174