SWS1233CQ0 Westinghouse Washer - Instructions

Remove front lower access panel: two phillips screws at the lower edge then the panel slid down and off. Removed 5/16 pump mounting screws then slid a shallow pan under pump to attempt to catch stale water, removed left side (inlet) hose clamp and wiggled hose off to drain water with some success, some spillage. Removed outlet hose, turned the pump around to remove electrical connection. Reversed steps to mount new pump and after fighting with spring clamp on outlet side I chose to replace that spring clamp with a 1 1/2" stainless hose clamp which then could be tightened with a screwdriver and only took a minute to wrap up.

Replaced drain pump using this walk through. Different models, but pretty straight forward.

Replacing all springs. Able to replace 2 short springs and front spring. Can't get to ones in back of washer tub. Unable to use strenght in arms to remove old springs. Help videos were great. Saved money by doing repairs myself.

I ordered pump so I would have it on hand. I didn’t want the washer in pieces waiting on parts. New pump came in 2-3 days with standard shipping. Found a video online for this model. Removed top. Removed control panel and set on front edge of frame. Removed door seal spring. Removed front panel and separated seal from drum. Pump located at bottom left. Removed pump screws. Got a shallow pan from kitchen to catch water. Removed hoses and trap. Not much water. Took trap boot and pump to sink for cleaning and found a bra wire had made it past the screen and was rubbing on pump impeller. That was the noise. Cleaned and reinstalled old pump. Has been running for 2 months without a problem. Easily returned the new pump! Highly recommend this company and site. Will come here for my repair jobs first. Hope I remembered all the steps correctly since it has been over 2 months.

Purchased both the belt and idler pulley. Bought the idler pulley "to have it if it were needed" since it was only a $15 part.

Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the video for each part.

Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.

I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.

Just like the video said in the parts menu remove front of washer remove 2 screws remove 2 hose clamps replace pump replace 2 screws replace hoses and clamps and front door to washer done

I had to remove agitator and clean under it.

Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.

Removed old belt. Installed new belt.

I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL

1. Turned off water to washing machine.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finished!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.

Removed two screws that held top of washer in place. removed top of washer. Removed two screws that held water inlet alve in place. Removed clamp and outlet hose from old inlet valve.












































































Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.

Pulled out the machine. Disconnected water lines. Removed four screws attaching the top brackets. In rear of top panel. Slid top panel forward and clear of valve. Removed two wire harnesses. Removed two screws holding valve to the back panel. Pulled valve down and out. Removed outlet side line spring clamp with channel lock pliers and pulled hose off old valve. Installed outlet side hose and spring clamp onto new valve. Placed valve up into place and installed two screws. Installed two wiring harnesses. Replaced top lid. Replaced lid bracket screws. Re-attached water hoses and pushed the machine back into place.

my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!

First I removed the hot and cold water supply lines to the machine. Then I removed the two screws at the top of the back panel, and pulled the entire top of the machine off which was a little tricky to figure out. There are two tension-like clips in the front of the machine holding the top on. (I had thought the back panel would come off so I was surprised when it became clear that the top of the machine would come off.) Then I unscrewed the two screws that hold the water inlet valve. I had to remove the green grounding wire that was clipped on the frame. The water inlet valve then lifted out easily. There were two clips to slide off, and a hose going into the tub that also had to come off which I did by loosening a little clamp on the end of the hose- saved the clamp for the new valve! Re-attaching everything was a snap. Tested the hot water before re-setting the top of the machine back together and it worked!