Models > SVD48600W Maytag > Instructions

SVD48600W Jenn-Air Range - Instructions

All installation instructions for SVD48600W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SVD48600W
16-30 of 300
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The LED clock assembly went dark!

  • Customer: John from Fraser MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 11 of 11 people found this instruction helpful
Turn off the power! Removed 4 phillip headed screws from beneath panel, (not the smaller phillip head screws at the each end). Gently tilted out the control panel, disconnected the wire harnesses, removed hex screws attaching clock assy to switch membrane. Cleaned a few items before re-assembly. put everything back together... You'll be surprised how bright the new assembly is...the old one gradually dimmed to the point it couldn't be read.

defective oven sensor

  • Customer: sean from easthampton MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 15 people found this instruction helpful
Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

Code said we needed a sensor

  • Customer: Janice from Portland OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

NO DISPLAY & OVEN WOULDN'T HEAT

  • Customer: CARROLL from ST. FRANCISVILLE LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 11 of 15 people found this instruction helpful
FIRST I REMOVED THE TWO SCREWS THAT HOLD THE BAKE ELEMENT. I THEN PULLED IT OUT FAR ENOUGH TO DISCONNECT THE TWO WIRES, AND REVERSED THE PROCESS TO CONNECT AND SECURE THE NEW ELEMENT. I THEN REMOVED THE SCREWS LOCATED UNDER THE CONTROL PANEL THAT HELD IT IN PLACE. I REMOVED THE WIRING, 3 CABLE CONNECTIONS, FROM THE CLOCK CIRCUIT BOARD, AND THE TWO SCREWS HOLDING IT IN PLACE. I INSTALLED THE NEW CIRCUIT BOARD, AND RECONNECTED THE WIRING, AND RETURNED THE CONTROL PANEL TO ITS PLACE.
THE WIFE WAS UPSET THAT SHE HAD OFFERED TO DO SOME OF MY CHORES WHILE I FIXED THE OVEN WHEN SHE FOUND THAT IT HAD ONLY TAKEN ME 10 MINUTES TO MAKE THE REPAIRS. THE PARTS WERE A PERFECT MATCH, AND THE JOB COULDN'T HAVE GONE ANY SMOOTHER.

oven door gasket was no longer flexible, but stiff

  • Customer: cheryl from dolores CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
pulled out the old door gasket, it had little diamond-shaped clips, pulled out really easily, replaced with the new gasket. All the clips fit into the proper holes, stuffed the new ends where the old ones were. Perfect. less than 10 minutes. Thanks....

Oven door snaping when closing

  • Customer: Mark from Sumner WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 13 people found this instruction helpful
Removed the door saftey plates lifted the door out of the hinge pockets, took the door to my work bench, removed six phillips screws which keeps the door glass cover in place, removed two screws form each hinge removed the old hinges put new ones back in place and reversed the disassembly procedure all in all about twenty five minutes.

One part of the grill burner came detached, caused fire at the connection

  • Customer: Anaclare from Oak Park AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 8 people found this instruction helpful
I turned off the burner and allowed it to cool. I then checked the website for the part and also got a new grease filter and grill grate. When the parts came, I plugged in the new grill burner, replaced the grill grates, and dropped the filter in place. Total time was about 8 or 10 minutes--most of which was opening the packages. The grill burner is designed so that it can be removed and replaced with a standard 2 burner unit. No tools were needed. I was glad to find the parts for my 17 year old dual-fuel range.

After self cleaning the oven received an error code telling me the sensor was bad.

  • Customer: Christine from Davie FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 11 people found this instruction helpful
Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

Many misc. electrical issues

  • Customer: Edmund from Fords NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
After removing the protective panel from the back, I used one of those screw holes to hold the new mother board right next to the existing one. I unplugged one connection & and plugged in to the new board. A couple of the wires didn't reach, but I committed those to memory. It looks a lot more intimadating than it is. It looks like a bunch of spaghetti, but its easier than it looks and it saved me at least $750

Lower oven intermittant operation-cleaning

  • Customer: Keith from Canyon Lake CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 11 of 18 people found this instruction helpful
Diagnosis is the important aspect. Ovens have plunger-type switches to tell the "brain" door is closed, both for the light AND to allow initiation of self cleaning. Finally discovered one of those switches was "scratchy" in operation and unreliable in closing the circuit. (Push the plungers in and out several times and observe the light.) If not 100% reliable, replace that switch (cheap and easy with a Phillips screwdriver.) Initial guess was a $major "brain"-electronics problem but it was merely a sticky switch. Strange since the unit is about a year and a half old and rarely used. Found the part easily with PartSelect, and it came via UPS quickly.

Oven would not shut down, kept heating

  • Customer: curtis from Paris IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 9 of 12 people found this instruction helpful
The front oven control panel was already in need of replacement. The digital readout had quit working sometime ago, so we began by replacing the control panel as well as the temperature probe. Neither of these items did the trick. Next I replaced the HI/Lo sensor switch. This replacement was a bit more labor intensive. Have to remove several screws and remove a large portion of the top of the stove. Once access is gained to the hi/lo switch, it takes (2) minutes to replace it. This of course did not take care of the problem either. Finally I replaced the bake/broil/convection circuit board. This was a bit of a job, only because of the amount of wires to and from this board. I litterally took a picture of the board (from this web site) and drew in the wires and marked them by color and noted where they went. I then merely unplugged each wire and with one screw, removed the board and installed the new one. After plugging in the wires as per my picture, SUCCESS. The board did the trick. Over all, it was not bad doing the work myself. I know we saved a lot of money my doing it ourselves. Just gotta have patience.

Oven failed to maintain the set temperature.

  • Customer: Thomas from Clarksville MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 7 of 7 people found this instruction helpful
Removed the old sensor by removing two screws and pulling the wire out through the hole. Disconnected the connector and discarded the old sensor.
Selected the correct connector of the 3 provided, plugged the new sensor in and threaded the wire back into the hole paying special attention to make sure wire and connector was on the backside of the insulation. Assembled the two screws and tightened.

You could not see any read outs. The screen was completely blank

  • Customer: Monty from Hellertown PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 7 of 7 people found this instruction helpful
The first thing I did was to turn off all of the power to the range. Then, I removed all of the screws and unhooked the front panel from the range. Then, I rolled the front panel upside down to get access to the wires. I then proceeded to disconnect all of the wires. After that, I removed the circuit board from the panel. Obviously, I just had to reverse the procedure to install the new circuit board. It was one of the easiest jobs I have had to do.

Clock display and associated annunciators had faded out

  • Customer: Roger from Deer Harbor WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 7 of 7 people found this instruction helpful
Removed 4 screws holding trim panel in place. Removed 4 screws on underside of clock panel

Pulled panel out slightly and disconnected the 2 electrical strips

Removed 2 screws holding clock assembly

Disconnected the ribbon circuit tape-push down on the holder tabs and simultaneously pull up gently on trhe ribbon.

Connect ribbon to new unit. Screw unit to panel.
Reconnect electrical strips and reinstall in reverse of disassembly.

Very easy to accomplish

Built in oven would shut down: fault code F-4

  • Customer: Edward from Juliustown NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 8 of 10 people found this instruction helpful
A few years previously I had this same problem and a PROFESSIONAL had replaced the sensor.
Thus this time I knew what the failure was and obtained the sensor from Part Select. Having observed the PROFESSIONAL replace the sensor before; I followed his easy technec only to learn that when the sensor was pulled from the aft wall of the oven that the wires had deteriorated and the plastic plug melted. Therefore it was neccessary to remove the oven from the wall cabinet. Then I removed the panel from the back outside of the oven, cut back the wires and because the kit from Part Select contained additional connectors was able to splice in a replacement connector. Installed the new sensor and reinstalled the oven. LESSON LEARNED; when the PROFESSIONAL had replaced the sensor he had failed to feed the wiring and plug back past the insulated chamber, directly behind the oven, into the cool area assessable by the panel on the aft side of the oven thus the plug and wires were exposed to the heat of the oven. What would commonly be a few minutes job turned into an afternoon project.
All Instructions for the SVD48600W
16-30 of 300