Models > SVD48600PK > Instructions

SVD48600PK Jenn-Air Range - Instructions

All installation instructions for SVD48600PK parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SVD48600PK
31-45 of 201
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven kept shutting off, getting F-3, F-5 messages on LED readout

  • Customer: ken from north andover MA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
I was out pricing new stoves. Why are slide in stoves twice the price of regular stoves?? I tried one last go at ordering part, overnight mail. Needed to get it fixed for the holiday meal. Part came within one day, early, and it worked. Stove fixed easily, spent the money on a big screen TV.

Both door hinges broke.

  • Customer: David from Woodinville WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
I removed two retaining screws that keep the hinges from falling off the stove. I lifted the door up and the hinges disengaged from their mounting pins. I put the door on the kitchen counter and removed the screws holding the stainless steel door cover on. The hinges have two small screws at the back of each hinge. I removed those and the hinge lifts out. I put a new hinge in and replaced the two small screws. I did the same on the other side. Then I picked up the door and put the hinge mounts through their respective openings on either side of the oven and dropped them into place. I replaced the retaining screws and that was it. Door hinges replaced! It literally took me about 15 minutes and I had never done it before.

Broiler blement failed

  • Customer: Donald from Hudson NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 10 people found this instruction helpful
Sunday, four days before Thanksgiving, our oven would not bake properly. A quick check indicated the top element was not working. What to do? Where to get a part in time to fix for Thanksgiving dinner? The answer was easy - PartSelect. I had the part in my hands on Tuesday AM. Oven was fixed in 15 minutes and my wife was baking pies within an hour. All worked well and yes, we had a wonderful trukey dinner. Great service !

broken glass Inside of oven door

  • Customer: ROBERT from Montclair NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 4 of 4 people found this instruction helpful
Removed Door- Removed outer stainless cover(6 screws) Removed the 1st 2 glass pieces. realized that there were 4 pcs of glass, not 2 as I thought. Found 2nd assembly of 2 pcs, of glass. The piece i ordered that was called inner actually only fit on the inside of the the two outer pcs, too small to replace what was the outer piece on the inside of the door. Called, returned 1st piece, got the correct one and reassembled.
Would have been easier if parts had more understandable labels such as inner door outside glass etc
beware when you order!

Self cleaning would not work on the oven

  • Customer: Crucita from Albuquerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 5 of 7 people found this instruction helpful
Removed old part with a pair of pliers and plugged the new part into place.

Very simple and the self cleaning feature works again.

Oven failed to maintain the set temperature.

  • Customer: Thomas from Clarksville MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 4 of 4 people found this instruction helpful
Removed the old sensor by removing two screws and pulling the wire out through the hole. Disconnected the connector and discarded the old sensor.
Selected the correct connector of the 3 provided, plugged the new sensor in and threaded the wire back into the hole paying special attention to make sure wire and connector was on the backside of the insulation. Assembled the two screws and tightened.

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

JennAir oven door very difficult to open and close

  • Customer: James from Morgantown PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
After reading three other reviews I decided to replace the hinges to save $ (REPAIR SERVICE ESTIMATE WAS $200 +). As another reviewer stated " I spent more time removing and cleaning the glass viewing doors than replacing the hinges". One critical part of the hinge replacement is the removal of the heavy oven door. TO AVOID INJURY DURING DOOR REMOVAL IT IS IMPORTANT TO INSERT A "PIN, SMALL NAIL, HEAVY PAPER CLIP" INTO THE SMALL HOLE ON THE ARMS OF THE HINGES. If you fully open the door you will see a small hole on one part of each hinge arm. As the door closes the arm with this hole slips between the other hinge parts. Inserting a pin will prevent the hinge from snapping shut when you remove the door and potentially smashing your finger with its strong spring. Once inserted you can remove the cover plate for the hinge pocket (one screw each side). Close the door to "broiling position" (about two/three inches open) and lift the door up off the bars within the hinge pockets to remove from stove. (Our SS range doesn't have sides so you could see how the door hinges just slip over and lock onto the pins in the hinge pockets.......the pocket trim covers lock the hinges on the pins during normal operation. At this point you just need to remove a few screws to remove the SS door skin to expose the hinges. Remove the one or two screws at the end on the hinge and lift that end up to slide the other end out of the retaining slots. Installation is the reverse...the replacement hinges have cute little pins that hold them open so, after installing on oven door, you can insert them into the hinge pockets and onto the pins as you hold door in the "broil position". After reinstalling the hinge pocket cover plates, you can open the door and easily remove the retaining pins. Sounds like a lot but probably would take approximately one hour if you don't remove glass for cleaning.

Parts were worn and dated.

  • Customer: Judy from San Jose CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
I removed teh pans and great filter.

I removed the screws from the older Rear and front burner assembly and use them on the new parts. It just took about 20 mins to do all 4 burners.

Checked that the gas worked for all 4 burnes once assembled. Then replaced the pans and the grease filler.

Results have been great as the gas burners ignite faster and the stove top looks brand new :-)

Oven wouldn't heat in any mode

  • Customer: Arnold from Augusta GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 3 people found this instruction helpful
Turn breaker off and start replaceing wires one at a time until you have the new part wired. Then secure new part and turn the breaker back on and it'll work. It's just that simple.

oven would not heat to set temp

  • Customer: Wayne from Seward AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
I rremoved two screws and pulled element out about 3 inches. I un hooked the two wires and tested with an ohnm meter to determine the condition of the element. Element was bad so I ordered a new one. Service and price were great. Easy fix. Thank you.
Don't forget to unplug first.

The range burners would not catch a spark and ignite. They would just keep clicking with no ignition.

  • Customer: Adrienne from Lake Havasu City AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
I had an appliance repair rep do the replacement. He made it look relatively easy.
The repair man first turned off the breaker to the range and confirmed there was no power to the range.
After lifting off the range top cover exposing the burner igniters, he unhooked and removed the igniters. He opened the lower oven door exposing the screws which hold the front knob plate in position. He took those out. After loosening the knob plate he was able to unscrew and raise the inside cover which exposes the wires and the spark module.
My spark module was located in the front left corner area tucked a little under the knob plate. That is another reason why he had to loosen the plate. The replacement part was a universal part so he had to do a little work on the wire connectors but it only took a couple of minutes. Once he configured the wire ends, he was able to plug in the new spark module and put the top back together again.
The repair man knew exactly what to do and made it look relatively easy. I did not want to tackle this problem because I did not know exactly where the spark module was since some models have them in the back of the oven and the oven has to come out from the wall. Also, the wire connections had to be worked with a little and he knew exactly how to do that.
The repair man took about 45 minutes from beginning to end with most of that time spent getting to the part and putting it back together. The replacement itself took only about 10 minutes.

Needed new filter

  • Customer: Vincent from Foxboro MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
Replace filter

Bake element wore out. Replaced Bake Element.

  • Customer: Roy from Rocklin CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Very easy. 1. Turn off power to oven. 2 move the adjustable grills out to gain better access. 3. There are two phillips head screws that hold a bracket to the back of the inside oven. Unscrew both screws. 4 pull the bake element out about 6". This exposes the two electrical connections. 5. Use a plier and wiggle the slide on connector off of the old bake element. 6. With your fingers, slip the old connectors onto the new bake element. 7. Slide the element and wires back in the insulated pocket. 8. Screw both screws back in. 9. Turn on power and make your wife back you chocolate chip cookies just to "test". Sit in an easy chair and enjoy your cookies. If this took longer than 30 minutes inclding baking the cookies, it took you too long. If the cookies are not good, replace the wife. May take a little loger though :)

broken hinge on oven door

  • Customer: william from medford OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
If I had known there was a shipping pin holding the hinge in place, it would have gone a lot easier. I thought I had the wrong replacement hinge but finally figured it out. A little note with the hinge indicating a shipping pin must be removed to complete installation would be helpful to idiots like me. Now that I know, the job is only a 15 minutes.
All Instructions for the SVD48600PK
31-45 of 201