Models > SVD48600PC > Instructions

SVD48600PC Jenn-Air Range - Instructions

All installation instructions for SVD48600PC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SVD48600PC
196-201 of 201
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

WHEN WE TURNED ON THE OVEN THE TEMP. READING WENT UP TO 425 AND BEEPED BY NO HEAT

  • Customer: DAVID from Cape Coral FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back WOW saved me $500. from buying new and $150. for service call

One set of burners would not ignite.

  • Customer: Brenda from New Market MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
This range is about 17 years old and the igniter on the left set of burners had failed in the first month of use. A warranty repairman came, made a big mess, marred the adjacent counter top, spent a lot of time badmouthing Jenn-Air and left without fixing the problem. We have been manually lighting these burners all this time. Now that I am retired, I have set about repairing everything I can get my hands on just to have things to do. I always did this when I was young but got too busy with career and family. One big help is doing things now is you can Google a problem, find parts and instructions how to make the repair which is much easier than all the research you used to have to do. This repair is easy but time consuming due to all the screws that you have to remove to get to the igniter and the controller in the back. Since one side worked I was confident that the controller was good but the problem was only the igniter on the left side. This range is a dual fuel unit and has a downdraft connection so sliding it out from the wall is also time consuming. First pull the breaker at the electric panel. Remove the bottom plate and disconnect the flexible downdraft connection. Hopefully, you have enough flexible gas line so you can slide stove out to reach the back without having to shut off the gas and removing the connection. Next you remove the grills and burners. Then you have to remove all the screws connecting the top of the stove. There are nuts and washers that surround the gas jets that you can remove to partially lift the drip pan so you can unscrew the old igniter and install the new one. Next remove the back and see where the igniter control is located. Disconnect the old wire, install the new wire in the guides and insert in the controller. At this point all you need to do is put everything back where it was. This does not take a lot of know-how just time and patience. It makes you wonder why an "expert" could not have done this easily.

change oven sensor

  • Customer: Lloyd from Eau Claire WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed provided video

Maytag range had "F3" code display, oven would not work.

  • Customer: phillip from Farmington NM
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.

Oven would not heat on Back Cycle

  • Customer: Jeff from Thousand Oaks CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Oven have F2 and F3 codes following cleaning cycle making oven inoperable

  • Customer: Timothy from Longmeadow MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!
All Instructions for the SVD48600PC
196-201 of 201