Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SVD48600B Maytag > Instructions

SVD48600B Jenn-Air Range - Instructions

All installation instructions for SVD48600B parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SVD48600B
61-75 of 317
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lightning zapped oven clock control assembly.

  • Customer: John from Corpus Christi, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Had estimates of $ 500.00+ to replace clock assembly. Purchased it at parts select for approx $ 200.00 and put it in myself. Will pocket the $ 300.00. Thanks. Turn breaker to stove off. Removed four screws underneath front panel. Must open oven door to access screws. Tilted the panel out from the bottom allowing the top of the panel to come out. Had to remove the two knobs on either side of the clock along with the clock knobs. When the two knobs on the side are removed it releases the mounting brackets for the clock inside the panel. Replaced clock assembly wires one at a time. Reassembled in reverse procedure.

Igniters did not spark

  • Customer: Steve from Sedona, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
Unplug and pull range away from wall.
Remove metal panel from back of range by using nutdriver to remove 4 screws.
Use phillips scewdriver to remove 2 screws holding old spark module.
Unplug 4 wires from spark module and note placement of wires for reinstall.
Install new module by reversing procedure.
Slide range back against wall and plug in.

Entire process took less than 30 minutes.

NOTE: Spark Module received from partselect.com did not match old part exactly. The screw holes on the new part did not line up with screw holes from old part. I reinstalled new part with just 1 screw. Was told by partselect customer service that the part I received had been substituted and would work fine. It does work but it did not fit correctly.

Bake element wore out. Replaced Bake Element.

  • Customer: Roy from Rocklin, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Very easy. 1. Turn off power to oven. 2 move the adjustable grills out to gain better access. 3. There are two phillips head screws that hold a bracket to the back of the inside oven. Unscrew both screws. 4 pull the bake element out about 6". This exposes the two electrical connections. 5. Use a plier and wiggle the slide on connector off of the old bake element. 6. With your fingers, slip the old connectors onto the new bake element. 7. Slide the element and wires back in the insulated pocket. 8. Screw both screws back in. 9. Turn on power and make your wife back you chocolate chip cookies just to "test". Sit in an easy chair and enjoy your cookies. If this took longer than 30 minutes inclding baking the cookies, it took you too long. If the cookies are not good, replace the wife. May take a little loger though :)

illuminated numbers were very dim

  • Customer: Howard from Ashland, OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
The range had to be pulled away from the wall to access all of the retaining screws. Once all the screws were removed, the top was easily lifted away, allowing easy access to the clock unit. Three wire connectors were also easily disconnected, and the clock was secured by only two accessible screws. Reassembly was straight-forward; the only difficult, and time-consuming part was sliding the range back against the wall, as tolerances were tight. The repair took 45-60 minutes and the clock shines brightly!

The (red) temperature display gradually went dark and the (green) clock display had lost about one third of its brightness.

  • Customer: Donald from Escondido, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 4 people found this instruction helpful
Turned off the breaker to the stove and removed the 4 screws under the control panel. The trim strip and the end caps did not have to be removed. The control panel was lowered just enough to clear the upper edge and then tilted forward so the connectors could be disconnected. Two screws holding the display in place were removed and the new display swapped out. Reassembly was disassembly in reverse. (My wife appreciates having a bright display again.)

I needed a broiler pan

  • Customer: Rhoda P. from Secaucus, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
I took the broiler pan out of the shipping container and put it in the oven.

20 year old burners were slow to light and hard to adjust for our propane fired stove. And, they were scratched and ugly

  • Customer: thomas from Goodrich, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Removed four screws; withdrew two burners; set two new burners in place; installed same old screws. That was it. When I turned them on to adjust the flame, they came on almost instantly and no adjustment was needed.

Wife loves the nice new look.

The range burners would not catch a spark and ignite. They would just keep clicking with no ignition.

  • Customer: Adrienne from Lake Havasu City, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
I had an appliance repair rep do the replacement. He made it look relatively easy.
The repair man first turned off the breaker to the range and confirmed there was no power to the range.
After lifting off the range top cover exposing the burner igniters, he unhooked and removed the igniters. He opened the lower oven door exposing the screws which hold the front knob plate in position. He took those out. After loosening the knob plate he was able to unscrew and raise the inside cover which exposes the wires and the spark module.
My spark module was located in the front left corner area tucked a little under the knob plate. That is another reason why he had to loosen the plate. The replacement part was a universal part so he had to do a little work on the wire connectors but it only took a couple of minutes. Once he configured the wire ends, he was able to plug in the new spark module and put the top back together again.
The repair man knew exactly what to do and made it look relatively easy. I did not want to tackle this problem because I did not know exactly where the spark module was since some models have them in the back of the oven and the oven has to come out from the wall. Also, the wire connections had to be worked with a little and he knew exactly how to do that.
The repair man took about 45 minutes from beginning to end with most of that time spent getting to the part and putting it back together. The replacement itself took only about 10 minutes.

Oven was not correctly heating to set temperature

  • Customer: Trace from Ofallon, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 4 people found this instruction helpful
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

After cleaning, F1-1 error flashed and neither oven worked

  • Customer: Georgene from Rock City, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

Needed new filter

  • Customer: Vincent from Foxboro, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
Replace filter

Oven Display Panel "Blacked Out"

  • Customer: Jim from Memphis, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
We operated the oven without the display panel for three years and finally discided to get it repaired. The cost of the repair was going to be over 330.00. I went online to PartSelect and had the part in a few days. I removed the 4 front screws behind each of the knobs, next I removed the 4 screws and 4 hex bolts under the front panel. The two side panels needed to be removed by taking out the screw from under each panel. Remove the front control panel and release the ribbon cable by pressing in on the two side tabs allowing the locking connector to be rasie up relaseing the ribbon cable. The other two power cable can be gently removed. Two hex bolts hold the disply panel to the front panel. Installation is the reverse of the removal process. The process took less then 20 minutes. PartSelect customer service was very professional and I will use them again without a second thought.

The Clock Display went out on our Jenn Air downdraft stove

  • Customer: Joe from Cedar Rapids, IA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
We simply removed the front knobs, the 8 screws underneath the front panel and dropped down the control panel. We removed two screws holding the assembly and removed the ribbon cable and the two other connectors. We put the new one in and reattached all the cables and reassembled and it worked great. Took 15 - 20 minutes.

No display on clock or oven status, auto light on burners not working, oven won't shut off.

  • Customer: James from Columbus, OH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
I removed the 4 screws that hold the control assembly to the range and observed that the clock assembly/control board appeared easy to remove.

Ordered the replacement board and it came a day sooner than the shipping I paid for. Only took about 10 minutes to take the control assembly off again and install the new.

There were no instructions with the part....the ribbon connection to the board was a little tricky to figure out...when I first released the clamps that held the ribbon to the board and pulled the ribbon out, I thought I damaged it....never seen a connection like this.

The range works fine now but it should be noted that this part is the logic control board for the entire range. The board malfunctioned over a period of time. First time, the entire oven shut down in the about half way through the preparation of Thanksgiving meal a few years ago. I couldn't bring it back to life and luckily, we had another oven to finish the turkey.

Next, we had trouble with the electronic pilots on the burners. You would turn the knob for one burner and it would attempt to light another burner.

Then the oven would not shut off when the Cancel/Off button was pressed. Would have to go and trip the main breaker to turn off the oven!

This replacement part cost $126 which is a bargain considering a new oven would cost over $2000. And it works great now. But I don't trust this appliance and I get this feeling that I threw good money after bad.

However, my experience with PartSelect was great and I will use them again. I just hope I don't have to spend more money on this applicance.

Replace the oven Sensor

  • Customer: Michael from Exeter, NH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 5 people found this instruction helpful
The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike
All Instructions for the SVD48600B
61-75 of 317