Models > SVD48600B Maytag > Instructions

SVD48600B Jenn-Air Range - Instructions

All installation instructions for SVD48600B parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SVD48600B
46-60 of 309
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

lighted display very dim to non existant

  • Customer: Dan from Burlington IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
Thanks to JP in customer service.

TURN THE POWER OFF TO THE STOVE at the breaker box!
I had to pull all the burner knobs off (4ea) and remove the screw under each one. Then open the oven door and remove the screws holding a trim piece on and the hex head screws holding the "touch pad panel" on (was also held on by the screws I had already removed from behind the knobs) 1 smaller screw at each end (total of 2) under there hold the plastic trim on that needs to be moved slightly to let the panel come out. (DON'T OVER TIGHTEN WHEN YOU REASSEMBLE) You hang the panel in the 2 slots provided and remove the old display unit. Gently unplug the 2 wire harnesses and ribbon that actually connect the touch panel to the display PC board. Look for the 2 small holes in the ribbon that will line up with the female part on the board. A piece on the board where the ribbon plugs in will slide up a little and allow you to plug the ribbon in and then push it gently back down. Finish putting it back together and turn power back on at the breaker box. Works perfectly.

Self cleaning would not work on the oven

  • Customer: Crucita from Albuquerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 5 of 7 people found this instruction helpful
Removed old part with a pair of pliers and plugged the new part into place.

Very simple and the self cleaning feature works again.

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

hard to get old one out

  • Customer: robert from chatham VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 14 of 35 people found this instruction helpful
easy to put in

The range burners would not catch a spark and ignite. They would just keep clicking with no ignition.

  • Customer: Adrienne from Lake Havasu City AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
I had an appliance repair rep do the replacement. He made it look relatively easy.
The repair man first turned off the breaker to the range and confirmed there was no power to the range.
After lifting off the range top cover exposing the burner igniters, he unhooked and removed the igniters. He opened the lower oven door exposing the screws which hold the front knob plate in position. He took those out. After loosening the knob plate he was able to unscrew and raise the inside cover which exposes the wires and the spark module.
My spark module was located in the front left corner area tucked a little under the knob plate. That is another reason why he had to loosen the plate. The replacement part was a universal part so he had to do a little work on the wire connectors but it only took a couple of minutes. Once he configured the wire ends, he was able to plug in the new spark module and put the top back together again.
The repair man knew exactly what to do and made it look relatively easy. I did not want to tackle this problem because I did not know exactly where the spark module was since some models have them in the back of the oven and the oven has to come out from the wall. Also, the wire connections had to be worked with a little and he knew exactly how to do that.
The repair man took about 45 minutes from beginning to end with most of that time spent getting to the part and putting it back together. The replacement itself took only about 10 minutes.

Parts were worn and dated.

  • Customer: Judy from San Jose CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
I removed teh pans and great filter.

I removed the screws from the older Rear and front burner assembly and use them on the new parts. It just took about 20 mins to do all 4 burners.

Checked that the gas worked for all 4 burnes once assembled. Then replaced the pans and the grease filler.

Results have been great as the gas burners ignite faster and the stove top looks brand new :-)

oven would not heat to set temp

  • Customer: Wayne from Seward AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
I rremoved two screws and pulled element out about 3 inches. I un hooked the two wires and tested with an ohnm meter to determine the condition of the element. Element was bad so I ordered a new one. Service and price were great. Easy fix. Thank you.
Don't forget to unplug first.

Oven wouldn't heat in any mode

  • Customer: Arnold from Augusta GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 3 people found this instruction helpful
Turn breaker off and start replaceing wires one at a time until you have the new part wired. Then secure new part and turn the breaker back on and it'll work. It's just that simple.

Bake element wore out. Replaced Bake Element.

  • Customer: Roy from Rocklin CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Very easy. 1. Turn off power to oven. 2 move the adjustable grills out to gain better access. 3. There are two phillips head screws that hold a bracket to the back of the inside oven. Unscrew both screws. 4 pull the bake element out about 6". This exposes the two electrical connections. 5. Use a plier and wiggle the slide on connector off of the old bake element. 6. With your fingers, slip the old connectors onto the new bake element. 7. Slide the element and wires back in the insulated pocket. 8. Screw both screws back in. 9. Turn on power and make your wife back you chocolate chip cookies just to "test". Sit in an easy chair and enjoy your cookies. If this took longer than 30 minutes inclding baking the cookies, it took you too long. If the cookies are not good, replace the wife. May take a little loger though :)

Lightning zapped oven clock control assembly.

  • Customer: John from Corpus Christi TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Had estimates of $ 500.00+ to replace clock assembly. Purchased it at parts select for approx $ 200.00 and put it in myself. Will pocket the $ 300.00. Thanks. Turn breaker to stove off. Removed four screws underneath front panel. Must open oven door to access screws. Tilted the panel out from the bottom allowing the top of the panel to come out. Had to remove the two knobs on either side of the clock along with the clock knobs. When the two knobs on the side are removed it releases the mounting brackets for the clock inside the panel. Replaced clock assembly wires one at a time. Reassembled in reverse procedure.

Self Cleaning did not work.

  • Customer: Rick from Beaverton OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 3 of 4 people found this instruction helpful
Remove burner knobs, Removed 7 screws from bottom of face plate. Removed screws from 2 alluminum or steel spacers I guess you could call them. I let the Op Panel hang carefully not to stress wires. I marked all wires of the Latch asm. Removed the four screws holding it in and carefully removed the wires. Replaced in opposite manner and self cleaning works. The oven tried to start the cycle but I noticed the latch never triggered. When the function first stopped working I was able to apply slight force to the door and the latch fired. So after replacing the door switch it still failed to work. So latch asm was the official fix. So I have had to replace the latch asm and the Op Panel for being dim. I don't think this model is very good. But Partselect.com is great easy to find parts and good prices. Very pleased with my experience.

illuminated numbers were very dim

  • Customer: Howard from Ashland OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
The range had to be pulled away from the wall to access all of the retaining screws. Once all the screws were removed, the top was easily lifted away, allowing easy access to the clock unit. Three wire connectors were also easily disconnected, and the clock was secured by only two accessible screws. Reassembly was straight-forward; the only difficult, and time-consuming part was sliding the range back against the wall, as tolerances were tight. The repair took 45-60 minutes and the clock shines brightly!

The (red) temperature display gradually went dark and the (green) clock display had lost about one third of its brightness.

  • Customer: Donald from Escondido CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 4 people found this instruction helpful
Turned off the breaker to the stove and removed the 4 screws under the control panel. The trim strip and the end caps did not have to be removed. The control panel was lowered just enough to clear the upper edge and then tilted forward so the connectors could be disconnected. Two screws holding the display in place were removed and the new display swapped out. Reassembly was disassembly in reverse. (My wife appreciates having a bright display again.)

I needed a broiler pan

  • Customer: Rhoda P. from Secaucus NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
I took the broiler pan out of the shipping container and put it in the oven.

Lower panal would not stay in place because plastic fastners were gone.

  • Customer: siri from remsenburg NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
I inserted the door strikes in the proper position and then snapped the panel in place.
All Instructions for the SVD48600B
46-60 of 309