Models > SVD48600B Maytag > Instructions

SVD48600B Jenn-Air Range - Instructions

All installation instructions for SVD48600B parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SVD48600B
286-300 of 309
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven temperature was of & then taking along time to heat

  • Customer: Barbara from Newark DE
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed video

replaced oven lightbulb

  • Customer: peggy ann from forest city NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy

Grease filter broke

  • Customer: Charles from Leighton IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Lifted the old one out and put the new one in. Very easy

Fan runs continually ,door locked,error code f2,f3,f7

  • Customer: John from Dacula GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with matched harness /.connection, installed 2 screws ,turned on breaker.

Inner glass of door was cracked

  • Customer: Leslie from Rome GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Slowly disassemled door from outside in. This included removing the section below the door to access the screws that were inserted vertically into the bottom of the door. There are hex screws and phillips head. There were several pieces of glass in the door that had to be removed to get to the inner glass. We finally lifted out a frame that held the broken piece and one other. Working on a flat surface we unlatched a small tab in one corner (pliers) and unwrapped frame just enough to release broken sheet. Wearing gloves we removed all the broken glass and gently inserted new piece. Realigning the other piece of glass we gently closed the frame reinserting the tab of metal and securing. Would HAVE to have two people to do this! We then reassembled the door reversing the process. Note: It is a SMALL hex screw.

The oven was not heating up to temperature

  • Customer: Max from Bothell WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the oven sensor which was easy to replace. A pigtail wire was provided with the sensor which is intended to be installed first so you don't have to reach around the front and back of the oven at the same time. The replacement was easy. However, that turned out not to be the problem. The real problem was the maytag electronic clock control timer, temperature control unit. The part number is 7601P177-60. This device has been discontinued and I was fortunate enough to find the part at a local supplier. Once I replaced this, the problem went away. The oven heats up normally. My original symptom was that when setting the oven temperature to something like 350 degrees, the display would rapidly report heating up the oven to that temperature, and the oven was only mildly warm. If you have that symptom, it is probably not the oven sensor. It is the electronic clock unit. Hope you can find one. If you can't, I think you need to by a new oven. Regards

Temp spikes.

  • Customer: Wayne from Grantsburg WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.

Oven control panel light dim

  • Customer: Warren from St. Joseph MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Open oven door, under the lip below the control panel there are 4 Phillips head screws and 4- 1/4" screws. If you have a screwdriver with interchangeable tips, you can use it for both fasteners. Remove the Phillips head screws first, Trim piece will drop down, clean while you have it out. Remove the 1/4" screws, the control panel will drop out about 4", it will be able to rotate towards you, you will see the display unit. Using a pointed knife, slightly pry the clip away and remove the two wired plugs. on the ribbon connector, on each side there are tabs, push these in and pull up not more than 1/8", the ribbon will pop out or take VERY little to remove, it is difficult, make sure the tabs on both sides are up. Remove the display via 1/4" screws. Reverse the process with the new unit but, make sure the tabs are up on the ribbon connector, this is the only thing I had problems with, took me about 3 min to figure it out. new display came with a "Static Electricity" warning. MAKE SURE YOU TOUCH THE FRAME OF THE OVEN BEFORE YOU TOUCH THE NEW DISPLAY UNIT TO AVOID STATIC DISCHARGE AND PROTECT YOUR NEW UNIT.

Had code F1 and F3 on my oven. Oven wouldn't heat.

  • Customer: Cindy from Polson MT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video and it was as easy as described. Not many things go as easily as this.

Oven would not heat

  • Customer: francis from mount holley VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

Wanted to replace old grease filter

  • Customer: Christine from Pembroke VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old filter, dropped in new filter. A breeze! What was best of all, is that Parts Select shipped the filter immediately and it arrived within just a day or so! Well done!

Filter was old and discolored.

  • Customer: Robert from Warroad MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The new replacement grease filter came without damage and it was a simple task of removing the old and setting the new in it's place. No tools were required.

only one burner on the cooktop worked

  • Customer: William from Chipley FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took two screws out of each burner and put new burners in and replaced the screws. A real piece of cake. and they work great. Did not even have to adjust the flames. They were all solid blue and perfect. Bill

display lights out

  • Customer: Frances from Riegelsville PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the first instructions that were listed on your site. Except I didn't need to remove the screws on each side of the turn on knobs. I just removed the knobs and then found out that I didn't even have to do that. The whole panel came down and I rested it on other pans so I could unhook the "cables" to the board. The most trouble I had was trying to unhook those cables. BUT once done, the job was a cinch. "I AM WOMAN - HEAR ME ROAR." Yes I did it all by myself and am quite proud of it too. Thanks so much for the instructions. VERY, VERY, helpful. Probably saved over $125 in service call-plus the markup of the dealer.

Replaced Grill with two burners

  • Customer: Michael from Topsham ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Very simple project. Had no clue it was so easy! To test how easy it is, remove the left side grill parts, move the grill parts from the right to the left! I had no idea there was a micro switch in the cooktop to change the fan operation! Parts arrived quickly. Only received one grate of the set, this was quickly fixed by Parts Select Customer service! We only used the grill once, made such a mess! Why did I wait so long to do this! (Over thirteen years!)
All Instructions for the SVD48600B
286-300 of 309