Models > SVD48600B Maytag > Instructions

SVD48600B Jenn-Air Range - Instructions

All installation instructions for SVD48600B parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SVD48600B
1-15 of 317
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replace Grease Filter

  • Customer: Gene from Washington C.H. OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 465 of 466 people found this instruction helpful
Just a couple of minutes to left off the cover grid, left out the old filter and drop in the new one.

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 67 of 72 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.

Needed to replace filter

  • Customer: Marie from New Smyrna Bch FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 91 of 153 people found this instruction helpful
Just placed it at the filter location. Liked the ring feature on the filter for ease of removal for cleaning. My previous ones didn't have such feature. Thank you for filling my order. I bought an extra filter for the future. I'm a big user of my Jenn-Air range. I may soon be needing to replace my griddle. Will be contacting your company then.

Lost all clock and timer display

  • Customer: John from Kuna ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 52 of 57 people found this instruction helpful
Removed the 4 phillip head screws that hold the trim plate on the bottom of the display panel (and you probably could skip this step).
Next, I removed the knobs from the front of the display panel.
Then I removed the 4 phillip head screws that were located (1 each) behind the knobs.
Finally, I removed the 4 hex head screws from the bottom of the front panel.
You caan then remove the panel a few inches and remove the two cable connectors.
The trick part is to get the flat ribbin cable disconnected. If you squeeze the two small tabs (one on each end of the connector), the connector moves up and spreads open to CAREFULLY remove the ribbon cable.
The clock assembly has just two hex head screws holding it in place. Remove them, and reassemble everything in reverse.
If you did everything correctly, you should have a very bright stove clock again!

Old grease filter was bent and needed replacing

  • Customer: Linda from Palo Alto CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 65 of 126 people found this instruction helpful
I simply lifted off the grille in the center of the stove, pulled out the old filter and dropped the new one in. It sits at an angle (right side down, left side up) rather than slotting in to a particular spot.

Replacing bake element as oven wouldn't heat

  • Customer: Catherine from Allenton MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 34 of 38 people found this instruction helpful
After viewing the diagram on partselect.com, I knew this would be easy. I first shut off the circuit breaker to the oven, then used a phillips screwdriver to remove the two screws on the plate securing the element. Once removed, I disconnected the two wires, and removed the old element. I then connected the two wires to the new element, and screwed the plate back into place. I then switched the circuit breaker back on and tested the new bake element which was working perfectly. This do it yourself repair saved me time and money not having to call and schedule a repair man. Thank you so much partselect.

Clock dimmed to very low, oven temp unreadable

  • Customer: Thomas from Moncks Corner SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 32 of 37 people found this instruction helpful
Was about to spend 2000 on new oven and decided to check here. At least 15 stories with same problem and solved. Add one more.

Only thing new to me was ribbon connector. Didn't really pay attention when I disconnected from the old assembly. When you squeeze the ends of the connector, part of the connector itself rises up to release the ribbon cable. Remember this when reinserting the ribbon cable on new assembly. If I hadn't followed the "If you have to force it, it ain't right" rule it could have gone bad.

F1-1 code

  • Customer: charles from marstons mills MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 24 of 27 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will cause the plastic plug connector to melt from oven heat.

Clock and all the readouts went "black". Stove still worked but no visible readouts.

  • Customer: Donald from Sausalito CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 22 of 27 people found this instruction helpful
First I turned off the electricity to the stove.
I then removed the 4 burner dials from the front panel. Then I removed the 8 screws under the front panel. Removed the triangle side pieces - 1 screw each. Slowly pulled the panel down and out and turned it face down so there was easy access to the back of the digital clock. Unscrewed the 2 screws that hold the clock and replaced it. New clock worked perfect. NOTE: Included in the repair - I cleaned and repainted where there was grease and rust.

Repeated oven temperature sensor fault codes.

  • Customer: David from Arlington VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 16 of 18 people found this instruction helpful
First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the right side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.

Display Fading to Black - Clock & Oven Temp Unreadable

  • Customer: Robert from Portsmouth NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 14 of 14 people found this instruction helpful
I did this job myself, but it might be handy to have a helper to assist in holding the control panel during unplug and replug stages of the process. Also strongly suggest you read through these and other posted instructions BEFORE getting started.

Kill Circuit Breaker Power To Unit.
Pull Four Burner Control Knobs off front panel.
Unscrew Phillips Head Screws from under each knob. (Be careful not to strip screw heads, I applied pretty firm pressure on screw driver to avoid stripping).
Open Oven door.
Remove 4 Phillips screws on trim piece under control panel and remove trim piece.
Unscrew 1 small Phillips screw on each side of panel to loosen plastic side trim pieces.
Use socket to remove 4 hex head screws holding control panel in place.
Gently pivot control panel top downward to access the circuit board panel. BE VERY CAREFUL NOT TO ALLOW CONTROL PANEL TO HANG BY FRAGILE CONNECTING CABLES!!!
GENTLY unplug the two white connector cables from the board. There is a locking tab on both that you can release with a fingernail or small flathead screwdriver while gently pulling the connector upward. (These connectors snap to lock more easily when you eventually re-assemble to the replacement board).
VERY GENTLY unplug the ribbon cable. This was a bit confusing to me at first, but if you gently squeeze the two very small tabs on both sides of the black connector, you can gently raise the center body of the connector upwards about 1/8 inch. (You might find it helpful to practice how this mechanism functions on your replacement part BEFORE you do the disassembly, it's really pretty simple once you see how it works). This will take the gripping pressure off the ribbon itself and you can gently wiggle the ribbon out free from the connector taking note of the two very small alignment holes in the ribbon connector as you do so.
Now with all cables free use a socket to remove 2 hex head screws holding the circuit board to the control panel.
Now install the replacement board by simply doing all above in reverse. Take care to line up cable connections to the board properly, noting the two alignment holes in the ribbon cable to tabs in the black connector. All three connections should snap in easily without undue force.
Your range display should be good as new.

Control no longer functioed, no vilible LED,

  • Customer: Paul from Tampa FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 15 of 18 people found this instruction helpful
The hardest part was learning how to access the electronic clock assembly. Once I figured that out the rest was easy. Finding your web site to locate parts was great. Having the esploded diagram for the Jenn Aire was very helpful.

Plastic clips had broken, causing bottom skirt piece to fall off.

  • Customer: William from Greensboro NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 14 people found this instruction helpful
After attempting to order this part from Whirlpool twice and twice receiving the wrong thing, found correct part on PartSelect in about one minute. Shipment came fast and the repair was very simple, under five minutes. You just pop the pieces in place and snap the piece back onto the oven.

The LED clock assembly went dark!

  • Customer: John from Fraser MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 10 of 10 people found this instruction helpful
Turn off the power! Removed 4 phillip headed screws from beneath panel, (not the smaller phillip head screws at the each end). Gently tilted out the control panel, disconnected the wire harnesses, removed hex screws attaching clock assy to switch membrane. Cleaned a few items before re-assembly. put everything back together... You'll be surprised how bright the new assembly is...the old one gradually dimmed to the point it couldn't be read.

Oven wouldn't heat the right temperature (you would have to add 100 degrees on to it)

  • Customer: Claudine from Bethlehem PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
Pulled oven out of the cabinet/wall and pulled sensor out and replaced with new one.
All Instructions for the SVD48600B
1-15 of 317