Models > STF7000FS0 > Instructions

STF7000FS0 Electrolux Washer - Instructions

All installation instructions for STF7000FS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the STF7000FS0
31-45 of 188
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door assembely had a snapped piece of plastic in unit.

  • Customer: DANIEL from STRATFORD NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
I released the door gasket and unscrewed the unit .Labeled the connections. then reconnected reattached, then put gasket back on. Worked like a charm!

Broken washing machine Vane

  • Customer: Ken from Rhinelander WI
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
Totally unable to move old vane using instructions on this site. Wound up breaking old unit in pieces to remove. Installed very easily. However when trying to install enclosed screw (which you are supposed to install through vane into tub) it did not line up even close to hole drilled into tub. I had wondered why the original vane didn't have a screw in it, now I know.

Drained but would not spin

  • Customer: Gregory from Louisville KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 10 people found this instruction helpful
The hardest part was figuring out how to get the lid off. You simply remove two screws from the back of the lid and jerk and slide the lid towards the back of the machine. Take out the screws that hold the front panel on, tilt the front out and access the lock/switch assembly and replace.

washer would not spin out

  • Customer: Linda from Dover FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 13 people found this instruction helpful
First called a repairman.Wanted over $300 to put a new door lock assembly in.Searched the web, found PartsSelect,bought part for less than $75,husband did repair in less than 30 min.
VERY happpy customer.

THANKS

Frozen pipe

  • Customer: Frank from Auburn NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 16 people found this instruction helpful
Removed top cover to get access to intake pipe for hot & cold water. Remove electrical connections and two screws replaced part and cover. Thanks very quick service.

locking mechanism spring broke

  • Customer: laura from willow creek CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
Watched video which was very helpful

Washing machine wouldn't drain

  • Customer: Siobhain from Ashland NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 7 of 8 people found this instruction helpful
i removed the front panel, then removed the old pump by taking off the clamps and disconnected the wiring. The new pump had to be reversed before connecting, but it was so easy.

Glass inner door cracked due to machine rocking

  • Customer: Gennaro from Nutley NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Simply removed several screws around inner glass Then part set right into place. replaced all the screws and was completed.

Thumping vibration on spin cycle

  • Customer: Kerry from Pasadena CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 9 people found this instruction helpful
Remove the front lower panel. Remove the 4 plastic pins mounting the shocks using 1/2 inch short socket to hold the detent down as per included instructions. All plastic pins were stuck in place so used needle nose pliers to pull or push out. Lube the pins with grease before reinstall to help them go through the new shocks. Use the included lock nuts to lock the four legs in place as low as possible. Start the washer and level each leg while running so you can tell if the vibration is going away. Tedious method but worked.

Door lock switch plastic bits broke

  • Customer: Herbert from Amherst NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
The previous posts made it dead easy - remove screws at the back holding top in place; slide top back; remove screws holding door latch assembly; disconnect three plugs, and connect new part. Replace fastenings, done! Throw up hands and wait for the official time;)

Spin Cycle wouldn't work

  • Customer: KEITH from BEND OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 7 of 10 people found this instruction helpful
Replaced pump, by removing back panel and removing the two screws holding the pump to the bottom of the machine. The only difficult aspect was dealing with the hose clamps, these were extremely awkward to work with in a confined space. The repair would have been less than 30 min if the hose clamps weren't so difficult to put back in place.

I had tried to clean the small basket type screens at the rear of the inlet valve but both of them disintegrated

  • Customer: George from INMAN SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 14 people found this instruction helpful
Following the instructions on your page I was able to see quite clearly what needed to be done. I received the new part promptly and my machine is now working fine. However, the ongoing story with the dryer is another matter.

Broken Face Clips on dispenser drawer

  • Customer: david from spring hill FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
I unclipped the old drawer parts from the broken drawer and replaced the old parts onto the new drawer and slid the whole drawer back in the washing machine. It took longer to type this that it did to repair the washer. No tools needed at all.

drum vanes broke

  • Customer: vernon from middlebourne WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 11 people found this instruction helpful
placed small plillips screwdriver in center hole of old vane and pulled vane toward front of washer and lifted up out of slots. (You need to press down tabs in center of drum slot to insert new ones) Placed new vane at front of slot and squeezed togeather so both sides went in slots and with screwdriver in center hole of vane pushed to rear of washer till vane locked. Incerted screw that came with kit to hold in place DONE.

Washer will fill and drain but will not spin or agitate

  • Customer: Gabriel from MERRILL WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Went by the percentage of people with same problem- door switch was the highest. Ordered door switch and a new belt (belt was getting worn- 6 yrs. old) Door switch did not fix problem. Saw on website that it could be motor control board. Took motor control board out. Nothing visible wrong with anything. Decided not to spend $$ on new board. Figured new washer would be better. Put motor control board back in and tried it......works like new! Must have been a loose wire on the motor control board. Next time I will check wires first. :) Getting motor control board in and out was time consuming but no too hard.
All Instructions for the STF7000FS0
31-45 of 188