Models > STF2940HS1 > Instructions

STF2940HS1 Westinghouse Washer - Instructions

All installation instructions for STF2940HS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the STF2940HS1
16-30 of 161
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water pump broke

  • Customer: Lili from Jamestwn NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 17 of 19 people found this instruction helpful
My Husband did the repair it took less than 15 minutes. He popped the front off the washer. He then unscrewed two screws and removed the pump assembly. He popped the new pump in, and put in the tow screws. Then he put the washer front back on replacing two screws. It took all of five minutes. I am so pleased it was so easy. I told him next time I'd do the repair and he could watch!
Lil

Dryer wouldn't go into high spin

  • Customer: Kristofer from Crescent City CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 17 of 21 people found this instruction helpful
this repair was easy, but it was repair #3.
#1: Fix-it guy said the front control board needed replaced. Ordered part from box store. Shoulda come here!
#2: Replaced motor control board. Harder to replace. Shoulda let the new front board run error code first. Again, used brand name supplier. Oops!
#3: Still not spinning. Error code "Door is open" but it's closed.
Remove door lock/switch assy, wires to the front board, and striker. 4 screws, 15 minutes. reached in through the top (did NOT unseat rubber around door).
Plugged wires into door lock. Inserted striker. Using multimeter on "Ohms" tested switch. No continuity=switch not closed.
New switch cost less, arrived faster. thank you Parts Select!

Tub wouldn't drain

  • Customer: Brian from Murfreesboro TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 17 of 22 people found this instruction helpful
First I removed the front panel,then set the timer to run. It began the drain,spin cycle, pump ran, but no water went out. Shop-vac the water out,removed hoses from pump,took out mounting screws from base, unplug pump plug. check hoses for debris since they're open, the impeller was broken. ordered the part . Mount the pump to the base, put the hoses on, plug in motor and replace front panel. plug into wall

door wont lock when turn on, it dont work

  • Customer: Jun from Alameda CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 16 of 20 people found this instruction helpful
took out door lock and switch assembly replace with a new one and it work

Drains but will not final spin

  • Customer: Chris from Naples FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 15 of 18 people found this instruction helpful
Great advice on your site.
Repairman "found bad motor control board" and gave me an estimate of $316.00 to repair. I figured that the $80 gamble was worth a shot. Took the top screws off, slid the top back and in less than 15 min. I had a fully functioning washer. Thank you.

Bottom door inge had gotten rusted so door was not closing.

  • Customer: Theresa from New York NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
Removed the old screws and old hinge. Put on the new hinge with new screws. Tightened 'em up and we were good to go. Pretty boring and basic. But beats the hell of not having the washer door close!

the pump had died

  • Customer: loudvik from glendale CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 13 of 18 people found this instruction helpful
First I removed the two screws that hold the pump in place. I then pulled the pump out and replaced it with the new pump.

Leak in the big hose connecting the pump to the washer

  • Customer: Robert from Schenectady NY
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set, Wrench set
  • 20 of 39 people found this instruction helpful
The top, control panel and front and back of the machine are removed - all by just removing simple sheet-metal screws. NOTE: remove the soap drawer, because there are two longer screws behind the drawer front. When replacing these later, get them just snug because "tight" will crush the supporting plastic. Don't bother to unplug all the wires to the control panel - just tape it to the top of the machine so it doesn't fall. The rubber part to be replaced is held to the machine by three large spring-held bellows clamps. Squeeze the ends with a pair of pliers and slide them off the tubing. When putting the new part on, I found that the cramped space and difficult access made getting two of the spring-held bellows clamps impossible to get back on, so I used automotive-style stainless hose clamps, which screw tight from the side. Be cautious to get them very snug but not super tight because, you can crush the plastic tubing to which you are fastening. Reassembly of the panels on the machine is the reverse.

Water not draining

  • Customer: Harold from Denver NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 11 of 13 people found this instruction helpful
It turned out that the pump was fine. There is a filter within the rubber bellows between the washer drum and the motor. You need to remove the entire bellows to get to it. Just remove the motor and you can un-clip the hose tensioners. They are exactly like the ones you would fine on most foreign cars - just compress with pliers and move back on the hose. Clean out the plastic filter. A small nail had worked its way through the plastic filter and lodged in the motor impeller. Removing this nail and reassembling, it all worked as new! I kept the pump and motor as a future spare rather than return it.

My washer would not spin. I had been told by the repairman that I needed all new control panels for my machine. The repair was going to be $540.

  • Customer: Angela from Houston TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 11 of 14 people found this instruction helpful
I read the input of others who had this problem with this washer and how they had replaced the door lock and switch assembly. I figured it was worth the $70-$80 part versus the $540 repair or purchasing a new machine. I was really happy with the machine until this problem occurred.
When I got the new part.....I unplugged the machine. Took out two screws in the back of the top panel. Removed the top of the machine. Took out two screws in the front of the machine that hold the door lock ans switch assembly into place. I unplugged the three wires from the old part (be careful not to drop the old or new part....if you choose to do this by reaching in from the top like I did for this repair.....easier than removing the entire front of the machine.)
I plugged the three wires into the new part and positioned the new part in the door lock position. Replaced the two screws. Put the cover back on the top and replaced the two screws that hold the top cover on the machine.
I was thrilled when it worked perfectly. What a relief!
Sure glad I looked at this website and tried this! The repairman really didn't know enough about my machine....obviously. I'd like to call him and tell what was really wrong so next time he'll know.

The washer wouldn't spin at all.

  • Customer: Leah from Ramsey MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
I unplugged the washer. Then I unscrewed the two screws on the back, top edge of the washer. and lifted the top off. Next I unscrewed the door lock/switch assembly, reached down in the machine from the top and pulled the switch out. As I unplugged each one of the three plugs from the bad part, I plugged them into the corresponding connections of the good part. Then I screwed the switch back into place, replaced the top of the washer and screwed it back on. I set the washer spin and cheered madly when it went into spin mode. The hardest part was actually turning the screws because I'm a small woman and my hand strength is not what it used to be. But really there was nothing difficult about this repair.

Washer would not spin

  • Customer: Terri from Glennville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 15 people found this instruction helpful
Ran diagnostic and discovered that the panel did not recognize that the door was locked, thus no spin. I ordered both parts, although I didn't need the door strike/catch. I only needed the locking mechanism. I removed metal ring from around the rubber piece inside the door with needle nose pliers, and then I simply plugged in the new lock and screwed it in place. I put the ring back around the rubber piece, flipped the circuit back on and washed a load of clothes. Easy as pie! Teachers can do anything. Who needs a repair man? :)

Frozen pipe

  • Customer: Frank from Auburn NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 18 people found this instruction helpful
Removed top cover to get access to intake pipe for hot & cold water. Remove electrical connections and two screws replaced part and cover. Thanks very quick service.

Machine would not spin.

  • Customer: Jeff from Weyauwega WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 12 people found this instruction helpful
Once I figured out that it would not spin because it did not drain. Unplug machine and remove the back pannel. Locate the drain pump on the bottom of machine. Remove the power wires and the screws holding it to the bottom. Then use a pliers to remove the hose clamps ( was easer for me to tip the machine forward ). Be prepaired to catch or soak up extra water from lines. The hardest part to the install is the limited room you have to work with. Install screws to hold the pump in place then install water lines, power wires and back pannel. Only thing left is to plug it in and watch for leaks.

door assembely had a snapped piece of plastic in unit.

  • Customer: DANIEL from STRATFORD NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
I released the door gasket and unscrewed the unit .Labeled the connections. then reconnected reattached, then put gasket back on. Worked like a charm!
All Instructions for the STF2940HS1
16-30 of 161