Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Spring assembly on detergent and rinse aid dispenser broke so the sliding lid would not operate
Here are the steps you need to take to do the job properly:
1. turn off electrical circuit breaker to the dishwasher 2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed. 3. unplug the wiring harness to the detergent/rinse aid dispenser 4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser. 5. the unit will pop out toward the inside of the dishwasher 6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in. 7. re-attach the wiring harness 8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job. 9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks. 10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.
I used a wet vac to remove the water from the dishwasher. remove cover and filter/strainer from bottom of dishwasher. remove screw which allows you to lift the plastic piece to access check valve. Original check valve looked like new , I installed new check valve re installed parts . Job done and issue resolved .
With the help of You Tube, this 50 year old Mom got the job done. Not that complicated if you watch the step by step instructions on the Appliance Pro video. My repairman and husband were both determined to just buy a new one but this 20 year old dishwashing genius was just in need of a little repair. Only need a screwdriver, and slightly confusing as wires hook on a little different on new pumps. I suggest watching video the whole way through and then playing it step by step as you do the repair. Worked great for me. Thanks.
Door on the old rinse additive would not stay closed.
Ordered the complete soap /rinse additive unit.nturn power off. Take the peripherical screws to remove the front of the door. Slide the door down and off. Unplug wires 2 places. Use a screwdrive to pry the tabs allowing the unit to come out
Important. Add a little Vaseline to the seal on the new part. Press it in until the tabs engage. Reconnect wiring and replace door front. Turn power on Job complete.
This is a piece of cake. No tools are actually needed. Grasp one end of the old seal and gently pull it out of the groove in which is fits. Take the new seal, and paying attention to which way around it fits (there is a right and wrong way!) start at either end. Leave an inch or so beyond the groove to rest on the bottom of the dishwasher, and press the seal in place in the groove. You should have an inch or so left at the far end. Go back and go all along the seal and make sure it is pressed evenly and completely into the groove the full length.
I did not know how to reach the part to be replaced so I took the base off and everything became complicated as I had to put it back, lots of electrical wires, houses aso.
To replace the part per se was simple. To put everything back in place was more difficult as I took the base of the dishwasher off and a lor of other parts in order to reach for the drain pump. The irony was, after I took appart the base I fount a clip on the internet showing how to do that job and that was a very simple thing, couple of screws to take off the toe plate and the interior liner of the door, to create good access to the drain pump. Really a job of 10 minutes at the max.
First of all, I quessed at what was causing the droning noise. It seemed that it started when the d.w. was draining. I looked at various sites to try and figure out what was causing the noise but they all wanted money up front before they would discuss the problem. I gambled that it was the drain pump figuring that, oh well at least it's a part I won't have to replace in the future. I got lucky, the noise stopped with the part I bought. The only issues were the wiring harnesss wasn't the same as in the video I used. Overall, your service was very good. The thing I'm disappointed with is the fact that my expensive Bosch d.w. had to be repaired.
One of the cabinet hold down brackets broke on Bosch dishwasher
I have granite countertops and one of the hold down brackets broke to wood cabinet side mount. Easy and fast repair to remove old brackets, pull out dishwasher, and I replaced both brackets with new, and new wood screws. New installation looks better than original done 18 years ago. Very easy to do and saved a lot of money if I had an appliance repair company do it.
Getting to the part at the bottom of the dishwasher was a little pain.
Everything went great installing the new drain pump. Our dishwasher works like it’s brand new again. I would recommend part select to anyone that needs to repair their dishwasher parts or any applications parts.
shut off water, pull dishwasher out, took side insulation off, unhooked what was connected to the float switch and replaced the new with the old. Reconnected everything and put insulation back and wa-la , all done