Models
>
SM230JXW2
SM230JXW2 Frigidaire Washer Dryer Combo - Overview
Sections of the SM230JXW2
[Viewing 6 of 6]Keep searches simple, eg. "belt" or "pump".
Main Terminal Block Kit
PartSelect #: PS471605
Manufacturer #: 5304409888
Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches...
$9.37
In Stock
Water Inlet Valve
PartSelect #: PS815509
Manufacturer #: 134190200
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve i...
$127.65
In Stock
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$11.21
In Stock
Upper Spin Bearing Washer
PartSelect #: PS473382
Manufacturer #: 5308002401
The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are ...
$12.94
In Stock
V-Style Belt
PartSelect #: PS459613
Manufacturer #: 5303280326
This v-style belt or drive belt is designed for use in your washing machine. This part connects the drive motor to the drive system in the washer, which spins the basket. If you notice a burning smell...
$37.34
In Stock
Levelling Leg Pad
PartSelect #: PS417749
Manufacturer #: 131422100
Sold Individually.
$13.44
On Order
Washer Bolt
PartSelect #: PS3655064
Manufacturer #: 137539500
Holds plated on Trunion .312-18 x 1.625.
$16.15
In Stock
Snubber Ring
PartSelect #: PS473378
Manufacturer #: 5308002385
The snubber ring on your washing machine mounts at the base, under the support. If you notice that your washing machine is vibrating, shaking, or moving during the wash cycle, you may need to replace ...
No Longer Available
Questions And Answers for SM230JXW2
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the SM230JXW2
[Viewing 8 of 8]Leaking
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer Continued To Fill To Point Of Overflow
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and remo
... Read more
ved the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
Read less
Parts Used:
-
alvaro from east hampton, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
86 of 96 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede
... Read more
d are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Read less
Parts Used:
-
Timothy from Spring Valley, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
95 of 148 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking washing machine.
Removing the piece above the tub gasket was very difficult. A lot of hammer and chisel work.
15 year old machine. A lot of calcium build up around the shaft. I used a screw driver as a chisel and a hammer. Carefully removed the metal around the shaft to get to the tub seal.
Once I got to the tub seal it was easy. Remove t ... Read more he old rubber stops. There were a few pieces. Then sealed it back up with the oil that came with the PartSelect Kit and put it back together. Works great now. No more LEAKS! Yippy.
15 year old machine. A lot of calcium build up around the shaft. I used a screw driver as a chisel and a hammer. Carefully removed the metal around the shaft to get to the tub seal.
Once I got to the tub seal it was easy. Remove t ... Read more he old rubber stops. There were a few pieces. Then sealed it back up with the oil that came with the PartSelect Kit and put it back together. Works great now. No more LEAKS! Yippy.
Read less
Parts Used:
-
Ron from Williamsburg, MI
-
Difficulty Level:Easy
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Socket set
24 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!