This part is a replacement tine row clip for your dishwasher. The tine row clip is adjustable, and it fits onto your dishrack to holds the tines into place. If your dishrack tine rows will not stay in...
$5.86
In Stock
Order within the next 3 hrs and your part ships today!
This seal is also referred to as a door gasket, and it is designed for use on dishwashers. It is installed on the door of the appliance, and it seals the space between the tub of the dishwasher and th...
$31.10
In Stock
Order within the next 3 hrs and your part ships today!
This micro filter basket assembly is used in dishwashers. The filter is responsible for filtering the water inside the dishwasher. All of the food and debris particles that are removed from your dishe...
$28.88
In Stock
Order within the next 3 hrs and your part ships today!
This is a replacement water inlet valve for your washer. The water inlet valve in your washer connects to the water source and solenoid wires, and ensures the tub has the right amount of water enterin...
$62.65
In Stock
Order within the next 3 hrs and your part ships today!
This door seal, also known as a door gasket, is an authentic manufacturer replacement part for your dishwasher. It is responsible for creating a watertight seal between the tub and dishwasher door and...
$43.16
In Stock
Order within the next 3 hrs and your part ships today!
A holder is used in dishwashers, it is known as the dishrack stop kit. This kit comes with both the front and the rear stop, these parts are installed at either end of the rails that the upper rack sl...
$12.03
In Stock
Order within the next 3 hrs and your part ships today!
This wheel kit is used for the lower rack of your dishwasher. The kit includes 8 wheels and axels. To install you can simply clip the wheel onto the frame. There are eight wheels on the lower rack in...
$44.42
In Stock
Order within the next 3 hrs and your part ships today!
First of all, wait till the replacement panel-facia arrives before removing the broken one. Look at the part. It has holes for switches, and It has two prongs that snap into slots in the metal front of the dishwasher. The panel-facia covers the electronic control contacts of the dishwasher, which are activated by plastic switches (or b
... Read moreuttons) set in rocker positions in the panel-facia. These are the On/Off, Power Scrub Plus, etc. The switches/buttons come off easily once you've removed the panel. Take care not to break these as you remove the old panel, because you'll need to put them in their respective positions in the new panel. The replacement part does not include switch/buttons. Now it's time to remove the broken panel. Open the dishwasher door and you'll see four screws at the top of the door (disregard those down the sides of the door; these hold the front panel to the machine, but do not need to come off.) Take out the four screws. The panel-facia has two plastic prongs that click into position on the front of the dishwasher, and clasp it in place. The screws you removed then secure the panel in place. To get the broken panel off, you need to pry gently but steadily at the two locations of the prongs, and you may have to break them. That's no problem, but do not damage the switch/buttons. Once the panel-facia is off, set each switch/button in its position, then align the prongs with the slots in the metal face of the machine, and snap it into place. Replace the four screws you removed previously. That's it.
Here are the steps you need to take to do the job properly:
1. turn off electrical circuit breaker to the dishwasher 2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed. 3
... Read more. unplug the wiring harness to the detergent/rinse aid dispenser 4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser. 5. the unit will pop out toward the inside of the dishwasher 6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in. 7. re-attach the wiring harness 8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job. 9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks. 10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.
I used a wet vac to remove the water from the dishwasher. remove cover and filter/strainer from bottom of dishwasher. remove screw which allows you to lift the plastic piece to access check valve. Original check valve looked like new , I installed new check valve re installed parts . Job done and issue resolved .