Models > SGR641HS1 > Instructions

SGR641HS1 Westinghouse Dryer - Instructions

All installation instructions for SGR641HS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SGR641HS1
46-60 of 349
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

drum glides worn out making thumping noise.

  • Customer: david from edinboro PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
watched video on replacing rear bearing.although rear bearing was not the part(s) i needed to replace, video instructed disassembly procedures to get to the drum glides. this was a very simple and easy to follow video. repair was a breezeand took roughly 25 minutes. the most time consuming segement of repair was vaccuuming out lint,that was 15 minutes. In future, as a preventative, i plan to remove front of machine to clean annually.
Thank you.

Broken Door Strike

  • Customer: William from Martinsville IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 5 of 8 people found this instruction helpful
After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

Squealing sound Idler arm and pulley

  • Customer: Lewis from Thornton CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 8 people found this instruction helpful
This is actually a white consolidated IND. brand, but that wasn't on your list. Be sure to check your tensioner pully if you hear squealing coming from the dryer. I changed the felt ring and the support bearing before realizing that my pully bushing was the cause of the noise. If you have squealing then spray a little wd40 on the bushing and shaft, if the noise stops, then you found the smoking gun. Replace the pulley. Unhook the spring and it comes right off. No tools needed.

Dryer runs but produces no heat

  • Customer: Richard from Appleton ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Unplug the unit. The top of the dryer is held down by 2 simple friction pins. By lifting the dryer top above it's front door panel the top will swing up. Prop the top up so you can reach down the front panel. There are 2 Phillips screws about 6 inches down on the dryers front panel. Remove the 2 screws, tip the front panel toward you it will slip off the dryer drum. Remove the 2 push on wires attached to the door switch. Gently lift the front panel off the 2 hinge points at the bottom and set it aside. The parts that your going to replace are the 2 solenoids on the burner assembly. The burner assembly is located on the lower left side of the dryer. Remove the 2 Philips screws that "clamp" the solenoids in place. Pull the 3 & 2 wire friction connectors off the solenoids. Lift the clamp off the top of the solenoids. Pick the 2 solenoids up off the valve assemble. Put the 2 new solenoids on the valve assembly push the wires back on, put the clamp back on and resemble the dryer. *Note: just to make a quick check on the continuity of the solenoids. I suspended the dryer drum so it could rotate without damaging it, put my clamp on amp probe on the 120v line to the solenoids the 3 wire one was good the 2 wire one was open.

Broken selector knob

  • Customer: Blanche from Mansfield PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Just pushed it on. The gray on the knob is a little lighter shade than the original, but not a problem.

dryer would make a sound when the button was pushed but no response from the unit

  • Customer: Sally from Newport News VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
I read your suggested test to determine where the problem was that was making the machine not start.
Got part . Took off back control panel. I put the part on as your instructions guided me . SUCCESS!
I set the timer and pushed the button and the dryer began turning immediately.

Felt around drum holder worn and torn.

  • Customer: Robert from York PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
1. Removed face of dryer (drum 'holder')
2. Disconnected door switch wires
3. Tore off existing felt

NOTE: The length of the felt that I recieved from PartSelect was incorrect (too short). Since the existing felt was worn and torn at the top, I replaced only a length that matched the length of the new felt.

4. Used a razor blade-type gasket remover/scraper to remove the exisitng glue
5. Applied new glue (which comes with the felt) onto the felt and let it set up

NOTE: In hindsite, I would apply the glue to the drum holder instead, as the glue otherwise soaks into the felt. If applied to the drum holder instead, the glue will spread out and provide more surface area for adherence.

6. Installed the new felt, starting at one end and working my way around to the other end, being careful not to stretch it
7. Trimmed the remainder of the existing felt (see first NOTE)
8. Scraped the drum holder below the pulled away ends of the exisitng felt
9. Applied glue to the existing felt, including the trrimmed ends so that the ends do not pull away from the ends of the new felt
10. Re-attached the existing felt
11. Let the glue set-up overnight
12. Reinstalled the face of the dryer, turning the drum so that the felt will not get pushed away
13. Reconnected the door switch wires
14. Turned dryer on, with lid still raised, to check for any drifting of the felt
15. Once assured that the felt would stay in place, put the dryer in service

NOTE: I replaced the felt becasue of the gap that opened due to compression of the felt. The gap, as well as a torn piece of the felt that entered the interior of the drum, was catching clothes and tearing them as they were rotated between the drum and the drum holder. The new felt eliminated this problem.

Loud Squeek while the dryer is running.

  • Customer: Miles from LaPorte IN
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 3 of 3 people found this instruction helpful
1. After checking the Parts Select website for some useful information I unplugged the dryer.
2. I popped the two clips holding the top down and lifted the top up and out of the way.
3. I used the 8mm socket and screwdiver combo to remove the two screws holding the front of the dryer on. These screws are so close to the sides of the dryer that you need something very thin to seat the socket, it is so thin a small rachet would not fit.
4. Once the to screws are free to forget to unhook the two wires that lead to the automatic cutoff switch on the right. Label them and move them out of the way.
5. The front of the dryer should pivot forward and come right off. Don't forget about the two clips at the bottom, they are not really attached to anything and can be easy to lose.
6. Get your screwdriver and dive into the drum, on the back should be three screws, take those out.
7. Spin the dryer around and take off the vent cover in the lower left corner of the back of the dryer, watch out the socket is a smaller size.
8. Once inside there is an idler pulley like on the back of a ten speed bike, pull the tension out of it and take the drive belt off the pulleys.
9. The drum should be able to be pulled out the front of the dryer, set aside with the door. The screws on my dryer were so tight I had to use a hammer drill to remove them.
10. This is were I got stuck, no one mentioned how to get the bearing plate off, as if everyone would just know. You must lift up on the bearing plate and once it moves up then you can pull it out.
11. Use the 8mm socket to unscrew the old plastic bearing guide. The small metal clip on the back of the dryer will fall off with the grounding ball bearing.
12. With brum bearing kit in hand start off by putting as much high temp lubricant as you can into the bottom of the new bearing guide. I also use a little lubricant like glue to hold the new grounding ball bearing in the little hole on the back of the bearing guide.
13. Here is the tricky part you have to screw the bearing guide into the the dryer while simulaneously holding the little metal clip in place on the back of the dryer. I used duct tape to hold the metal clip and once the screws got started I just took the tape off.
14. Now you have to do the impossible, the bearing must be screwed to the drum. So unless you have 7 foot long arms you can't hold the bearing and drive the screws. Another problem is the bearing itself, the holes are not the same size as the original and they are not threaded. I stripped every screw that came with the kit trying to get them through the metal of the bearing.
15. With an unwilling victim holding the bearing steady I finally got a replacement screw to seat through the bearing. Once you get one the rest are easier.
16. You are ready to reassemble, after vacuuming everything ou, pick up the drum making sure the belt is around the drum about where it was when you took it off. Push the drum through the front of the dryer all the way to the back, aim a little high so the bearing can move down and seat in the bearing guide.
17. Tuck the clips on the front panel of the dryer into the bottom front edge of the dryer and the whole front should pivot up, when you get it almost closed you will have to lift the drum and set it on the front bearing in the door.
18. While holding the front of the dryer on you have to reach inside and get the 8mm screw started on the left or right, if you let go the front of the dryer will pop off and you have to start over with the pivot. Now is a good time to have a magnet on a stick so when you drop the screw or screw driver you don't have to take the front off to retrieve your tools.
19. Once the front is on reconnect the two wires to the switch in the front of the dryer. Remember the ones you were supposed to have labeled earlier.
20. Close the top of the dryer and spin the dryer around so you can reach inside the vent door and pull the tension pulley over and reseat the drive belt. Rem

Blower wheel was raddling

  • Customer: jena from loganville GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 11 of 27 people found this instruction helpful
The blower wheel was a bit difficult, but manigable to do yourself.

Burning odor, melted terminal block

  • Customer: DAVID from DURHAM NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 3 people found this instruction helpful
0) Turned off breaker at panel and disconnected power cord from 240v wall outlet
1) Removed screws that hold electrical cover plate on back of dryer.
2) Lifted the top of dryer using putty knife on 2 top edges of lid. This lifts up like a cars hood.
3) Removed the screws that attach the power cord to the terminal block and disconnected power cord
4) Removed screws that attach terminal block to dryer
5) Removed melted terminals by prying out of terminal block. Note metal lip on terminal has to be lifted in order to slide connector out. Also unscrewed ground wire from terminal block to dryer.
6) Drew diagram of what color wires go to what terminals
7) Cut terminals off of wires and connected new terminals. Crimped closed and used butane solder torch to solder connection between terminal and wire
8) Reconnected terminals to terminal block by sliding in. **Note, had to file down the edges of the terminals using moto-tool to make it fit as they are connected together using break-away tabs that leave a large piece of metal connected not allowing to fit in terminal block
9) Reconnected terminal block to dryer and reconnected ground wire.
10) Reconnected power cord to terminal block with screws
11) Replaced cover over wiring terminal block
12) Reconnected power cored to 240ac wall outlet
13) Turned breaker back on

Terminal block, and wires were dammaged/melted

  • Customer: Edwin from Eagar AZ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Used nut driver to remove screw and cover from dryer cord terminal block, used screw driver to remove two screws securing old terminal block, cut dammaged wire and stripped wire back and crimped on new terminal connecter, replaced old terminal block with new one, replaced two screws, installed new cord, and replaced cover plate and screw.

Screeching noise when drying

  • Customer: David from Rockville MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.

Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)

Re install everything back again. And you are done

Front drum guidesnubber ring was worn out

  • Customer: Alan from Emporia KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
removed the top of dryer, pulled front panel back from drum and installed snubber(Front Drum guide).

dryer door part broke

  • Customer: Bonnie from Saint Augustine FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.

Drum guides came out into dryer

  • Customer: lloyd from celina OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Removed old guides ( some of the snap in fastners were broken off). REplaced guides by rolling drum, easy to snap in @ drum bottom each time.
All Instructions for the SGR641HS1
46-60 of 349