Models > SGR641HQ0 > Instructions

SGR641HQ0 Westinghouse Dryer - Instructions

All installation instructions for SGR641HQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SGR641HQ0
61-75 of 267
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken dryer belt

  • Customer: Lee from Sunbury PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
removing was easy just open lower rear LH panel . Ordering was easy ,shipping seemed like alot? to install the new belt pop top of dryer I used a screw driver to help. remove front panel 2 screws then it also has about six clips may have to have gloves on so you do not skin your hands like I did.... lots of sharp edges. pay attention to the clips, so if they come off they will not be lost. panel will tilt slightly fwd then raise up and set aside. now you can slip the belt over the drum. I kept all the slack at the top till it was in position. the groved rubber side goes against the drum and the motor pully. then extend the spring tensioner into position . I rotated the drum a few times by hand to make sure everything was in position. replace front. check it is lined up well before forceing clips in. check felt material is properly in place, as you rotate it into position. push down top . good to go. I ran it for awhile watching everything work before placing it back in service. you may want to clean it out some while it is apart I used an air compressor and shop vac simultaniously as that seemed to work best. Wanted my son to do it as I think he had it over loaded as to why it broke? It maybe the bearings are going but it felt solid ?? I should find out in a month or so shich was which! I did not see any easy way to get to grease it. The belt was easy though pretty sure my son could have handled it!

Black lines and small tears

  • Customer: Robin from Sewaren NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Previous comments on line were so helpful.

My husband and son took the dryer apart by removing the top in order to get to the drum. Part of silver rim that the Drum Glide is attached to was broken,it had been cut somehow. They had to soder it back in place so they could attach the Drum Glide and so far it's working.

Felt- I just ordered one with the adhesive and removed the damaged section used a wire brush, applied the adhesive ( which was more than enough) waited a few minutes for the adhesive to set, applied the felt, attached binder clips to hold it in place while working on the Drum Glide. Really easy.

Dryer had Loud squeek, barely spun!

  • Customer: John from Edgewater MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
First, I shut off the gas & unplugged the dryer. Then I disconnected the vent pipe so I could pull it away from the wall to access the back. Disassembling the dryer was simple.
there are 8 screws: 2 for rear access panel, 2 for top, & 4 for front panel! Once front panel is off, lift back of drum up 2 inches, then forward to get rear bearing out of it's bracket. My rear bearing had worn down so much it was 1/2 the size of the new one! It wore through the bracket down to the metal! I replaced the rear bearing & bracket assembly, as well as the belt & the spring for the belt tensioner! make sure you generously lubricate the new bearing as well as the tensioner pulley! The most time consuming part of this job was cleaning all the lint out the dryer cabinet& cleaning the drum. It works great now! I hope to get a few more years out of it!

Temperture switch broke

  • Customer: Steve from Merrick NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 2 of 2 people found this instruction helpful
Unplugged the drier, a couple of screws, remove the wires (take a picture of the wires with your cell phone to remember how they go back, twist out the thermostat. Installation is the reverse. A piece of cake.

female part of door clasp broke

  • Customer: Tammy from St. Peters MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
All I did was push the new part into the machine! So easy!

Latch on dryer no longer worked

  • Customer: chris from dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

howling dryer. Wolves in the area would howl back!

  • Customer: David A from Deer River MN
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 2 of 3 people found this instruction helpful
Waited only 2 days for part. That was with REGULAR delivery. It usually takes weeks to get out to REMOTE northern Minnesota.
Unstacked the dryer took off the top. 2 screws to open front. Pulled 3 drum mounting screws. Pulled the drum. Removed the pivot. Cleaned (blowed and vacuumed everywhere). Cleaned the pivot receptacle. Relubed the pivot with high temp lube. Removed 2 motor assy mounting screws. Screwed off the squirrel cage. Swapped the motor. Remounted new motor assy. Looped belt over drum. Remounted the drum. Closed the front. Closed the top. Opened the belt access plate on the rear. Looped new belt over the tensioner. Closed the access plate. Restacked dryer. Turned it on. Sounds like brand new. Less than 2 hours. Saved more than $800. More than I generally make an hour! Actually I saved a lot more than $800 because I probably would have had to buy both the washer and dryer stack so it could have been around $2500.
Everything I ordered arrived in 1 box and all parts are right!
Now in my spare time I need to replace the bearings on the old motor and I'll be ready for the next time, in another 10 years!

Dryer wasn't heating

  • Customer: Jack from Huntingdon PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Determined that the coil on the gas valve wasn't pulling in to ignite. Using an ohmmeter, I determined the coil was open. The coil was removed by pulling off the wire connecter and removing the two phillips screws holding the bracket over the two coils. The coil then slides out. I slid the new coil into place, replaced the bracket and two screws and reconnected the wire connector. It worked immediately. The actual repair only took 15 minutes. The bulk of the time was spent tracking down which part had failed.

Lound noise inside dryer

  • Customer: Joseph from little Egg Harbour NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.

Tumbler not moving

  • Customer: Francis from Middletown NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 2 of 4 people found this instruction helpful
Removed back panel. Popped off top of dryer, then removed front of dryer. Slid belt onto tumbler, put front cover back on, put top back on and adjusted belt frombottom panel cover.

dryer was squealing loadly

  • Customer: MIKE from MASSAPEQUA PARK NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 1 of 1 people found this instruction helpful
took off face of dryer, removed drum 4 screws removed two srews holding bearing and shaft ,replaced shaft bearing and shaft . Just for preventive maintenance i replaced idleling arm and dryer belt. I lined everything up replaced drum used shop vac to clean lint and dust from all parts replaced face of dryer and boom i got a btand new dryer

The clothes were not getting dry, no matter how long they ran

  • Customer: Bruce from madison OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
The first thing I did was logged onto the internet to search the web for my dryer information. Next, after I found the correct model, the site referred me to the parts section and that is where I determined the problem was the M series ignition coil. I then unplugged the dryer and turned off the gas. I took a screwdriver and popped the top off and cut the wire straps that held the door strips and the light to the front panel. I then unplugged the door switch at the connector - HOWEVER - DO NOT TRY TO REMOVE THE WIRES FROM THE ACTUAL DOOR SWITCH BECAUSE THEY ARE VERY FRAGILE AND CAN EASILY BREAK. Next, I removed the two screws that hold the front panel on. By using a slight bit of pressure, I removed the front panel and was able to locate where the ignition coil switch was. (It was right in front) I then removed the two screws that held the clamp down, as well as the bad coils. The coils easily slid off the post and the new pieces slid back on just as easy. I then replaced the screws and clamps to hold the new pieces in place and replaced the front panel. **NOTE ~ while the front panel is off, it would be a good time to clean out all the built up dirt and lint that has accumulated over the years. Lastly, I re-connected all switches and wires and replaced the top panel. Once I turned the gas back on, everything ran beautifully.

Dryer drum stopped spinning

  • Customer: Ron from Senatobia MS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
First I took the drum out of the dryer. This was an easy tear down. I had to remember 2 wires, and a belt assembly ( 2 pullies ). I removed 3 screws inside the drum to release the bearing assembly from the back. Then I went to the dryer chasis and removed the mounting bracket by removing 2 screws. I simply replaced the mounting bracket with the new one. This required having to use a magnet to hold a small ball bearing in place while I worked the rest of the pieces in position.I greased it up and went back to the drum. I replaced the old bearing assembly with the new one. Easy. I took the time to shop-vac the inside of the dryer. There was a lot of loose lint, candy rappers, coins, etc. Finally, I put it back together. Unfortunately, this is the forth (4th) time I've had to do this. It's cheaper than buying a new dryer. Now, I've got to fix the washer.

Dryer making horrible squeaking sound when running

  • Customer: SHARON from SUMMERVILLE SC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 1 of 1 people found this instruction helpful
I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.

Broken dryer belt

  • Customer: Sean from Hewitt TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
1.Removed access panel on back of machine in order to place a block under the drum(see step 3).2. Removed the top (clips), 3.removed the front panel(clips), block placed under drum earlier prevents drum from tilting and makes removing front panel with door very easy.4. Slipped new belt on. 5.Replaced front panel and removed block under drum. 6. Aligned belt and checked movement of drum, 7. attched belt to pulley on motor and positioned belt tensioner.8. Installed top and access panels.
This repair is very straight forward, block under drum makes things easy, since the drum stays level when the front panel is removed and replaced.
All Instructions for the SGR641HQ0
61-75 of 267