SGR351HS1 Westinghouse Dryer - Instructions

I followed instructions I found on u-tube to remove the drum and belt and access the bad bearing and change it. The instructions were quite good other than needing to remove a small panel on the back of the dryer to pull the belt around the tensioner.

DIsassembled the dryer by removing the top piece first. Removed the kick panel and the two screws on the bottom of the front panel. Disconnect the 2 wiring harnesses then remove the remaining 6 screws that you can see from the top. If possible, have someone support the front panel as you undo the last couple screws. Remove the plate on the rear lower right side to expose the pulley and belt. Pull on the tensioner while gently pulling the belt off the pulley and tensioner. Lift the drum up quick and hard to separate the ball shaft from the bearing holder. Remove drum by taking it out through the front opening. Replace the ball shaft on the back of the drum. This is much easier if you have an extra set of hands. At this point, vacuum out as much lint as you can. There is a white container attached to the front panel, vacuum this too. THere was several inches of lint build up that had made it past the screen. Replace the bearing, ball retainer, and ball bearing on the dryer. Grease the ball and retainer and reinstall the drum. SInce I was replacing the bearing, I went ahead and replaced the belt too. Reposition the belt on the pulley and tensioner. Spin it a little to make it is on the right place. Reassemble the dryer. This is the first time that I have done a repair of this sort and it turned out to be a lot easier than I thought. Two people would have made it even easier and faster.

Followed the video, it was good, the instructor's tips were useful and time saving.

I suspected a worn belt and that's what it was. I watched 2 videos on belt replacement and it was not a hard fix. The only "problems" I could foresee would be moving the drum around if you are not that strong. Its not terribly heavy, just a little awkward. I also sliced the top of my hand a little on the underside of the cabinet when moving the drum. Being a little more careful that wouldn't have happened. Part plus shipping was less then $20, and we now have a great working dryer again. I also got a zap when I forgot I had plugged it back in and was putting the inside screws back and the screwdriver crossed some wires. Nothing bad, just a quick jolt. Remember to unplug it until you're all done!

Remove top cover 2 screws then remove front panel 6 screws remove wire connecter on the door panel. ignition coil is on the bottom left side need a short hand srew driver remove 2 screws remove plate holding coils remove coils and connecter. Reinstall in reverse installation. Dryer still didnt heat up so back to the drawing board :)

The repair was done by my spouse. We replaced the rear drum bearing. We installed with the instructions sent by parts select. They were very accurate. The total repair took about 1 and 1/2 hours that was only because we cleaned out the entire dryer also, by using an air compressor to clean and blow out all the lint built up. This improved drying time and the part stopped the noise. I don't recall exactly what tools were used besides screwdrivers. This was our first time to replace anything in our dryer of 12 years old. I feel that if you follow the instructions that anyone would be able to do this repair. We did the repair in our garage because you need the room to work on it.

First I have to say that this was the fourth appliance repair I've done with Partselect parts. I am very pleased with all parts I've gotten from Partselect. The things I've ordered here are delivered quickly and are correct. Now for the dryer repair. I guess the most important tool I had to complete the job was the excellent video demonstration on the Partselect web site. I found that by following the instructions on the video even I had no problems. I spent more time cleaning the inside of the dryer than I did on installing the rear drum bearing. I probably saved us several hundred dollars by making the repair myself. At first I was intimidated but after I got the top off of the dryer and the front off the repair was simple and straightforward. Total time of repair was about fifteen minutes. Total time spent cleaning the lint and other stuff (I did find two dimes and a penny) was about forty five minutes. One hour total and my wife and I have a dryer which is acting like it did when we purchased it in 2001. Thanks to Partselect. Barry

I highly recommend watching the repair video. I could stop the instructions and do the procedure then resume instructions for the next step. I would recommend you have a second person to help lift the drum up & out of the dryer frame. And ladies please instruct your husbands to watch the video all the way through. Mine lifted the top off the dryer and stuck his hand in and cut his finger immediately on a sharp piece of metal. You know because they don't need to read the instructions.

I watched the video and the instructions were perfect. The only thing I did differently was I had a second person help me to hold the bearing spring and hold the drum knob in place. I also used the rear access panel to disengage and re-engage the belt because I know I am not good at doing things blindly. You will definitely want to pre-thread the knob assembly before you screw it to the drum. Glad the kit included a bearing because the old one was completely gone. It took me so long because I took the opportunity to vacuum 10 plus years of lint and I was using it as a teaching opportunity. If I have to replace the heating element I think it will be much faster.

It was super easy! I followed the PartSelect video and everything went fine. Getting the drum out of the machine was a bit tricky but once it was out, the rear bearing kit went in without any problems.

Pushed on new knob.

I watched the videos on this excellent website first. Then the repair was a breeze.

installed the back bearing with the ball bearing and dropped in the rear drum bearing and tried to install the drum to the rear drum bearing, but we could not find the screw holes to attach the drum, we tried and tried and finally I came up with the idea to take the drum out and screw the drum bearing while we had it ouside and that worked out beautifu lyl and all we had to do was reinstall the drum and all we had to do was lift it up just a little and drop it into the retainer rear retainer' and then all we had to do was install the tension roller which we had a little trouble but we finally figured it out and now it works just fine, it would a lot if there was a diasgram included on how to re-install the tensioner

Removed the panel between the dryer and washer. The gas valve was right in front. The wires were in a plug and easy to remove from old part. The solinoid held in place by a clamp with two screws.

it was so easy using the video that you emailed me. I want to rebuild my whole drier now .