Ask our experts a question about this part and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rich
December 21, 2017
What is the ohm of this part? Im trying to determine if my thermo is defective before i purchase this part
Hi Rich,
Thank you for your question. Your thermostat should read 0 ohms when testing it at room temperature. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Paul
February 2, 2018
Is the safety thermostat used with this dryer instead of a thermal fuse, or does it have both?
For model number 41790052990
Hi Paul,
Thank you for your question. It looks like your appliance just has a cycling thermostat and this safety thermostat. The safety thermostat would replace the thermal fuse. Some models actually do carry both but yours only has the safety and cycling thermostats. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Michael
August 27, 2021
Regarding the safety thermostat l180-40f, what does the 40 represent? Is it a temp differential for the t-stat closing? In the slim event is has failed, 1%, would it be ok to substitute a fusible link with the same or close specifications?
For model number AGQ7000ES1
Hello Michael, Thank you for the question. The 40f is the limit where the Thermostat is triggered to start to raise the heat and not allow the temperature to go under 40F. We can not recommend a substitute sorry, we can only suggest replacing the part when defective. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Brian
February 3, 2024
What should be the Ohm reading on the 2 pronged coil on the gas valve?
For model number DG27A5WAFA
Hello Brian, thank you for reaching out. According to our research, the two prong coil should read 1,000 to 1,300 ohms across prong 1 and 2. We hope this information is useful!
Was this helpful?
Thank you for voting!
Michael
October 7, 2017
Is the switch normally open or closed?
Hi Michael, Thank you for the question. The Safety Thermostat shoudl read closed. Hope this helps!
Was this helpful?
Thank you for voting!
Terry
May 10, 2019
I am having trouble with my gas dryer the burner will light and burn for approximately 30 seconds then it goes off after approximately two minutes it will relight and goes off again and keeps repeating this cycle is this normal or is the high limit thermostat causing this to happen i would appreciate any information that you could give me it is taking a long time to get my clothes dry thank you. Terry
For model number 41798042701
Hi Terry, thank you for your question. When you are experiencing an issue like this there are a few parts that you will have to test to determine what is causing your issue. For all of these parts you can test them with a multi meter. First you will have to test your thermostats and thermal fuses to make sure they are all functioning correctly. After that you will want to test parts in this order, your m series coils, igniter itself, or your radiant flame sensor. You may also want to check your regulator just to make sure that part is functioning properly as well. Something else you should also check would be your filter and ducts. Make sure there is absolutely no blockage that would restrict air flow in your appliance. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
Maximino
June 13, 2019
When this parts is wrong what happend to the dryer
For model number wgr211eso
Hello Maximino, thank you for your question. If this Safety Thermostat for your model was faulty, it could cause the heat to go out or to overheat in the dryer. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
