SGR351CS0 Westinghouse Dryer - Instructions

put on new knobs they match perfectly

This video by Steve Ash was spot on . In our case the white rear support bearing had melted and reformed around the shaft, preventing us from being able to pop the drum in the way described in the video. We used pliers to unscrew the screws on the rear clip from the back of the dryer. The rest of it worked exactly as described in the video. Our model was White-Westinghouse DE600ADD1, which is not a model listed on the PartsSelect website. However the part worked very well. The dryer runs really quite now.

1. Removed the back plate on the switch control panel, 6 screws. Twisted the old switch to release tabs from slots and inserted new switch, reversing the twist in the tabs provided. Connected the two electrical terminals on the switch. Tested operation. Screws the back panel back in place.

Pried the lid up and flipped it back then disconnected the front panel wiring harness and then popped the front panel loose at the top and dropped it down. Disconnected the ignition coils, removed the coil retainer bracket and replaced the coils. Reassembled it in reverse order, performed functional test. Success!

-remove screws on top of dryer -check for clips on side -remove panel under control panel -remove screws (6) I think, holding control panel -disconnect door switch connector -remove 2 more screws holding front -you may have to lift the tub to allow the vent tube to clear for front removal - - Proceed with felt seal portion of repair - - - -GOOD LUCK You may need help.

Ordered new knob and pushed it on.

You tube has quite a few videos that walk you right through the entire process. Due to the age of my dryer I replaced the belt and the Rear Drum Bearing kit while I had it apart. There were videos for all of it. Easy fix.

The belt arrived in 2 days. I cleaned the inside and it took no time to replace the belt. All I did is removed the front.The video was very helpful.Your magnet is on my refrigerator for future orders. Thanks.....Andy

followed vidio instruction which made it easy

purchased bearing kit

Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!

I wanted to know why my dryer was making such an ear-piercing screech. Googled, and found Steve at PartSelect. After watching the 10 minute video on how to replace the rear drum bearing, I knew this was something we could do at home. I ordered the parts on Friday and they arrived on Monday. Also ordered a new drum belt and drum glide. Didn't know if we would need those parts, but figured while we had the dryer apart, we might as well replace them. My husband watched the 10 minute video the following Saturday, and together we replaced all 3 parts. The original bearing was small enough to fit through the hole (which it shouldn't) and metal shavings we all over the plastic holder. The large metal ball attached to the dryer had grooves worn into it. The kids we amazed, too! I can't believe the repair was so easy! Seeing the inside of the dryer makes me wonder why they cost so much! Do not hesitate to make this repair yourself. Even just one person could do it.

Never knew I was handy, but I did it! I was reluctant to spend a couple $100 on a repair visit, so found this site and bought the coils I needed for only $26+tax. It's pretty easy. I just lifted up the top of the dryer with a screw driver, should snap open. Then unscrewed the front panel with two screws from the inside. Then located the old coils on the bottom left. The bracket that holds them is a little difficult to remove as you need to have a small philips screw driver to get the back one. But once I got that off, just unplugged the old ones and put the bracket back, then the panels and it WORKED. The only problem I have is that I didn't take the door switch off properly and now the dryer doesn't stop spinning if I open the door and want to check the clothes. So I may have to get someone in eventually.

Follow instructions all most to the letter. In video it was stated to get an assistant to hold static / housing retainer in place to start screws. I put it in place and, used Duck Tape to hold it there while i started screws. Thanks for the deal on parts and, video. I would also suggest advising to check the nylon strips on felt at the front top. Mine were worn. But there was enough at the back of nylon to remove and, glue remainder in place almost as good as new. Again! ''THANKS!''

I remove the drum, and install the bearing just like the instructions in the video.