Models > SGR351CS0 > Instructions

SGR351CS0 Westinghouse Dryer - Instructions

All installation instructions for SGR351CS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SGR351CS0
361-373 of 373
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer Squeaking

  • Customer: Gilbert from Elizabethtown NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Found instructions on "UTube"some of the screws were in a different position but you can see them. While you have the dryer apart it's a great time to clean it and also as long as you've gone this far replace the belt,it's probably time.

I shut the door too hard, and the old latch fell down into the inside of the dryer.

  • Customer: Bret from Tampa FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The new latch easily snapped it into place.

Dryer selection know and turn-on broke

  • Customer: Robert from Plano TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simple and your company provided the right part, amazing quick, at the best price and resolved our issue. Thank you!

Loud screeching noise until the dryer warmed up

  • Customer: Marila from Portland OR
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
My order confirmation email had a "how to" video for installing the parts I ordered. I just watched the video, and the installation was ridiculously easy! We've put up with the obnoxious screeching noise for probably about two years, and with about $40 in parts and less than an hour of work time, we have practically a new dryer!!

needed to replace drum bearing

  • Customer: Jon from Jenkins KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took front panel off, removed access panel in rear to disconnect the belt from motor. removed top panel (this is a stack unit) take plastic rivets loose from lint trap, remove lint trap tube, pull drum out after slightly pulling up to dislodge drum from bearing cradle, Remove bracket and bearing from back of unit, clean parts of old grease (be carefull not to loose small ball bearing on back) Reassemble parts using moderate amount of new grease, put parts back together in reverse order.

Dryer making scrubbing noise while running

  • Customer: David from Raven VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
This is a front load dryer. First unbolt top cover of dryer. Then unbolt screws and connections to control panel. Next unbolt all screws holding dryer door and front bottom panel. Next take belt off of drum and slide out drum from the front. From inside of drum remove 3 screws and remove bearing then put new bearing on and bolt up the same way you take old one off. Using an 8mm socket or wrench remove plastic bearing cage located at rear of dryer. When unbolting there is a retaining clip and small steel ball to be removed from back of dryer. Replace this the same way you take it off. He sure to grease the bearing cage then replace everything back from putting the drum in first to your last step bolting on top cover of dryer. Hope this helps anyone doing this repair.

worn bearing, squeaking, scraping sound

  • Customer: Terry from Lancaster OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I have used this company twice now and both times have been a good experience. Would highly recommend!

Broken belt

  • Customer: Jim from Middleboro MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Many thanks for the video you guys put together on replacing dryer belts! I didn't know how I was going to get inside the dryer. I had the dryer apart in 10 minutes! Had to wait a day for the belts to come in. New belt in and dryer running in 15 minutes! Thanks for running a first class operation!! Jim

Broken belt; Second one in 2-years.

  • Customer: Edward from Sayville NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I heard the dryer running, but I didn't hear it tumbling like usual, so I got suspicious. I popped the top off of the dryer to reveal a broken belt. Installation took 20 minutes.

Loud squeek when running

  • Customer: Kristina from Draper UT
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Could not figure out how to get into the dryer. Wasted a couple hours trying different things. Found a video online which showed the repair I wanted to make. After that it was easy. One needs to be tall and in shape to lift the drum out of the case....or have the help of a second person. Only a little blood was shed but now feel confident I can replace any of the parts in the dryer if needed.

Dryer just barely got warm

  • Customer: J Martin from Guerneville CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Everything I needed to know was already on your website. Prying off the top of the dryer (with a big screwdriver under the front of the top) was the hardest thing, since I was afraid I would break something. Only then can the front be removed (taking out just 2 phillips screws). The rest is easy.

no problem

  • Customer: David from Mayfield KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
put door catch in hole

garment damage

  • Customer: Michael from Paragould AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed your very helpful video instructions. Saved me a ton. Five stars!
All Instructions for the SGR351CS0
361-373 of 373