Models > SGR351CQ0 > Instructions

SGR351CQ0 Westinghouse Dryer - Instructions

All installation instructions for SGR351CQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SGR351CQ0
16-30 of 301
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer would not ignite

  • Customer: David from Murrieta CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 16 of 18 people found this instruction helpful
Make Sure Dryer is off and disconnected from power! Also, beware of sharp edges on dryer parts and cabinet.
1) Popped-off top lid with flat-blade screw driver (Insert screw driver in joint between top and front of dryer above door) Spring clips are all that's holding top on in front
2) Unplugged plastic electrical connector located just along the top-right side of dryer
3) Removed one sheet metal screw located about 8" down from top on either side of dryer - total of two screws
4) Pull front of dryer back and pull up at bottom of dryer (Remember that when you replace front you will have to make sure plastic bearing surfaces on dryer tub are centered back in cut-out on front panel. Plastic tabs fit inside the cut-out or else you'll ge a swishing noise when tub rotates)
5) Set front panel to side
6) Flame sensor is located on the left side of the burn chamber sheet metal cover. It has a red and white wire with flat connectors that must be pulled off. Note which color goes to what terminal
7) Unscrew fastener. Note: this screw/fastener needs a non-standard driver to get it out. I have a variety of other drivers beyond phillips/flat types and non of them worked.
8) I ended up using a pair of pliers to just work it out from under the screw. I bent it, as it has a tab that slips in along left bottom edge of burn chamber cover.
9) Finish taking screw out by hand
10) Put new flame sensor in by inserting tab on bottom first. Then, screw in fastener to top of sensor bracket and reconnect wires. White on top and red on bottom terminal.
11) Replace front panel with door by placing in tabs on bottom front of dryer. Again, make sure plastic bearing surfaces are inside of circular flange on front panel
12) Make sure to reconnect plastic cable connector. Note: I added a tie-wrap because it looked like the connector might rub against drum. There are some holes through which you can run the tie-wrap
13) Replace the two sheet-metal screws
14) Push top down so spring clips re-engage with dryer body

no heat in the dryer

  • Customer: Joy from Lakeville MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 15 of 18 people found this instruction helpful
unplugged the dryer, discontected the sensor and unscrewed the bracket, replaced the new one and put the connectors back on, screwed the bracket back on and that was it. Very easy fix for a female who does not do much of these sort of repairs but learning.

lint filter did not fit "squarely" into its place

  • Customer: Jeff from Bethalto IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 14 people found this instruction helpful
replaced old filter, only to find that the new one had the same issue. After closer examination, I determined the filter guide that screws into place, which I had removed earlier to clean lint out, did not hold the lint casing correctly. I removed and reinstalled the piece that has the metal moisture sensors, and replaced it, ensure both screws held the lint casing as it should. Now I have two lint filters that fit perfectly! So, if you ever remove the piece wtih the metal sensors, make sure that the lint casing is screwed in correctly when replacing.

the burner wouldn't ignite

  • Customer: Michael from Newbury Park CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 12 of 12 people found this instruction helpful
UNPLUG the appliance. After removing the top of the dryer the front is easily removed. To make life simple I disconnected the wire harrness at the quick disconnect and placed the door/front away from the workspace. I removed the bracket holding the coils in place and replaced the old with the new coils. replaced the front and top panels and pugged it in! Good as new!! I originally ordered the wrong part and PART'S SELCET.COM refunded my money no problem! I will bookmark this site and use it again.

black streaks on clothes from failed drum glide and felt

  • Customer: Rodney from Mountain View CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 12 of 13 people found this instruction helpful
first i used a flathead to lift up the top of the dryer. there were two prongs that you press in to detach the top.

then there were two screws on the inside along each side that i needed a phillips to remove. one screw on each side.

i also needed to detach a cable and cut the tie.
from there, it was easy to pull off the front of the dryer.

the first noticeable thing was HOW much lint there was inside! so out came the vacuum and away went all the dust and lint.. a TON of it.

then i used a sharp knife to remove all the existing upper and lower felt. that took awhile, and i got as much as i could.

then i applied the TOP felt, nice and center, and from there, the FELT was applied, which fit perfectly. I let it dry/set for about 2 hours.

for the Front drum glide, AN IMPORTANT NOTE! i ordered only ONE drum glide, but you need TWO! I had to order a second one, and i dont know why they dont come in pairs.. so the front drum glides snap on pretty easily to the front of the drum. press hard and they SNAP into place. once they are snapped on, you just put back on the front, replace the screws, re-connect and re-tie the cable, and close the lid!

Motor shaft broke

  • Customer: Beverly from Blairsville GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 12 of 14 people found this instruction helpful
had to remove the belt and drum and then remove the motor and replace it...put the belt on and then the hard part was to get the drum in place without the belt coming off. New Motor works quieter than the old one did, so I assume the dryer came with a defective motor to begin with and then the shaft finally broke. It runs very quiet now, but never did before. Even a service man came when it was new but said that was normal. Now we know it was not....there was a problem from the start.

Drum making thumping noises, clothes getting caught behind drum.

  • Customer: Gerald from Baltimore MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 11 of 11 people found this instruction helpful
I've always been a "do it yourselfer". If I can fix it, I save money. I took the dryer apart by lifting the top up like car hood. Then I removed the front panel. The front drum glide snapped into place easily where the other one had broken off. The felt strip that you sent was much shorter than the one on the dryer, so once I used the wire wheel to remove the old glue, I cut off the section of the felt that was bad and replaced it with the new felt. The turns much quieter and clothing doesnt get caught behind the drum anymore.

My husband ruined the old latch by trying to shut the door too hard, and the old latch fell down into the inside of the dryer.

  • Customer: Michelle from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 13 people found this instruction helpful
I took the new latch out of the package and snapped it into place. It took about 15 seconds, and that included the walk to the laundry room!

Old Dryer drum veins degraded and broke down.

  • Customer: Alfred from Loveland CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 9 of 12 people found this instruction helpful
I opened the top of the dryer to gain access to the outside of the drum. Then I removed the screws holding the old drum veins in using the electric drill with the nut driver attachment. Then I positioned the new veins in place on the inside of the drum and replaced the screws from the outside of the drum to hold the veins in place. Then I replaced the top and was ready to go.

This is the third repair that I have done using parts from parts select. the other two repairs involved replacing electrical parts. Specifically thermostatic controls or swicthes. I am very happy with the parts and the diagrams provided on your web site without wich I would have had to replace my dryer a long time ago.

Squealing sound Idler arm and pulley

  • Customer: Lewis from Thornton CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 12 people found this instruction helpful
This is actually a white consolidated IND. brand, but that wasn't on your list. Be sure to check your tensioner pully if you hear squealing coming from the dryer. I changed the felt ring and the support bearing before realizing that my pully bushing was the cause of the noise. If you have squealing then spray a little wd40 on the bushing and shaft, if the noise stops, then you found the smoking gun. Replace the pulley. Unhook the spring and it comes right off. No tools needed.

The dryer drum wouldnt turn

  • Customer: Kara from Beckly WV
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 9 of 13 people found this instruction helpful
Had to pretty much disassemble the entire dryer. The schematics on the web site made it a snap to do. One word of advice. I you have to replace the rear drum assembly, the drum has to come out the front of the dryer. Part select made this a very positive experience.

Gas Dryer would not heat; Drum turned

  • Customer: Anna from Palo Alto AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
Internet Search suggested that I check the Igniter, Sensor, thermal cutoff and Ignition Coils. down in the bottom of the Gas Dryer. With top cover off and front panel on, I put a mirror down in the bottom of the Dryer. I watched to see if the Igniter and the Sensor would turn on the Gas Valve. In the reflection of the Mirror, I could see a glow, but heard NO clicks. Repeated several times. Same Result. I suspected the Ignition Coils were faulty.

You suggested replacing BOTH. Parts arrived in 2 days. :-) Easy disassemble and reassemble with screwdriver. (Front Panel must be removed). While I was at it, I replaced the Drive Belt, too. It was 6 years old.
Everything worked fine.
After 6 years in a Garage, the Dryer was filled with Dust. Use the opportunity to Vacuum out the dust.

Burning odor, melted terminal block

  • Customer: DAVID from DURHAM NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 7 people found this instruction helpful
0) Turned off breaker at panel and disconnected power cord from 240v wall outlet
1) Removed screws that hold electrical cover plate on back of dryer.
2) Lifted the top of dryer using putty knife on 2 top edges of lid. This lifts up like a cars hood.
3) Removed the screws that attach the power cord to the terminal block and disconnected power cord
4) Removed screws that attach terminal block to dryer
5) Removed melted terminals by prying out of terminal block. Note metal lip on terminal has to be lifted in order to slide connector out. Also unscrewed ground wire from terminal block to dryer.
6) Drew diagram of what color wires go to what terminals
7) Cut terminals off of wires and connected new terminals. Crimped closed and used butane solder torch to solder connection between terminal and wire
8) Reconnected terminals to terminal block by sliding in. **Note, had to file down the edges of the terminals using moto-tool to make it fit as they are connected together using break-away tabs that leave a large piece of metal connected not allowing to fit in terminal block
9) Reconnected terminal block to dryer and reconnected ground wire.
10) Reconnected power cord to terminal block with screws
11) Replaced cover over wiring terminal block
12) Reconnected power cored to 240ac wall outlet
13) Turned breaker back on

dryer drum squealing loudly!

  • Customer: john from waynesboro VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 7 people found this instruction helpful
THIS UNIT IS A STACKABLE WASHER&DRYER,SO FIRST PULL UNIT AWAY FROM WALL ATLEAST 4 FOOT.UNPLUG POWER CORD,THEN TAKE10 DAGREE FRONT PANEL OFF THEN THE CONTROL PANEL OFF AND UNPLUG THE 5 CONNETORS IF YOUR UNIT HAS THAT MANY,THEN LAY PANEL ASSIDE.TAKE DRYER DOOR OFF,MAKES IT EASIER WHEN PUTTING IT ALL BACK TOGETHER.NOW TAKE FRONT PANEL OFF AND THE DRYER LENT TUBE,NOW JUST TAKE THE 3 CENTER PHILLIPS HEAD SCREWS OUT AND SLIDE DRUM OUT.PULL UPWARD ON WHAT THEY CALL THE SHAFT WHICH HELD DRUM ON.NOW THESE ARE THE PARTS YOU SHOULD ORDER.BELT,GROUNDING BALL CLIP,GROUNDING BALL,DRUM SUPPORT BEARING,BEARING BRACKET,AND MOST IMPORTANT PART IS THE SHAFT.THE SHAFT IS UR INSURANCE FOR THE WHOLE JOB.USE A GOOD GREASE LIKE WHITE LITHIUM GREASE AND COAT THE SHAFT END AND THE DRUM SUPPORT BEARING.THE GREASE WILL CUT DOWN ON FRICTION FOR A WHILE,AND RE ASSEMBLE THE WAY YOU TOOK APART.REMINDER GROUNDING BALL GOES BEHIND DRUM SUPPORT BEARING NOT IN FRONT.GOOD LUCK AND PLEASE VACCUM.

No heat/intermittent heat. Ignitor glowed but no gas flame.

  • Customer: Jeffrey from Richmond TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
White Westinghouse WDG547PB Dryer. Removed access panel (lower left front of dryer) by removing phillips head screw below access panel. Removed two phillips head screws holding bracket that holds coil in place. Removed coil, disconnected electrical connector. Connected electrical connector to new coil and set in place. Repeat for second coil. Reinstall bracket and access panel. Job complete. Dryer back in service with no problems.
All Instructions for the SGR351CQ0
16-30 of 301