Models > SGR351CQ0 > Instructions

SGR351CQ0 Westinghouse Dryer - Instructions

All installation instructions for SGR351CQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SGR351CQ0
271-282 of 282
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Turn type start switch, knob set screw came loose, further use destroyed switch stalk and twisted it out of fixture.

  • Customer: Roger from Laramie WY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Check that power cord is still disconnected from initial inspection. Remove chassis cover plate. Count and set the screws aside. Check type and fit of replacement. Twist-lock new switch into place. Swap wires onto proper terminals of new switch. Replace cover plate. Replace and tighten switch knob. Re-connect power plug. Activate new switch. Three tests successful. Return dryer to ready position. Test again- OK. Repair complete.

Loud squeaky noise

  • Customer: Alexander from GREECE NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
My dryer was making a horrible squeaking noise comparable to nails on a chalkboard! I looked to get a similar used replacement because I was in a bit of a pinch for $$$, after being frustrated and not finding anything I came here and found all the parts I needed for my repair for UNDER $40!!!! I followed the super easy how to video that was provided on this website. This is the second repair I have made to this dryer, I did the heating element about a year ago. I also used this site to purchase the part and used the how to video associated with that repair. I was very surprised that I received the part the next day when I paid for regular standard shipping! Overall this was a an awesome experience and I have saved so much money repairing my dryer on my own vice paying someone to do it!!!

dryer was making a shrill noise

  • Customer: Mike from Goldonna LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed the front then removed the belt that turns the drum pulled the drum strait up from the top then removed the bushing from the back wall put the new one in I also put A little grease in the new bushing to keep it from wearing installed the drum and front. realy easy. I'm A Instructor at A technical collage in Winnfield Louisiana and I used this as A project for my students.

drum belt

  • Customer: MANUEL from SAN JACINTO CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
so easy my daughter installed it the video was very helpful

drum making noise

  • Customer: Fred from Cle elum WA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
remove top lid (snaps and remove ground wire), remove front, 2 Phillips screw; remove nylon stop (Phillips screw) remove belt from motor (access plate 2 Phillips screws). Lift back of drum from pivot, remove from cabinet. check heating element for distorted or damage coils. Straighten or replace. clean felt surface and install new felt with glue. install new sliders in drum. assemble, rotate, listen for scraping. there should be no scraping sound when rotated. scraping can be from the heating element being distorted from lack of air flow because the drum stalled. If not fixed the heating element will be damaged when powered

Loud screeching noise, barrel turned OK and Heater worked

  • Customer: Ellen from Willits CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I took the lower back panel off. Loosened the center bolt and took off the old Idler pulley. It looked brown in the middle and didn't roll well. But I wasn't sure if that was it, because the noise was so loud and sounded metal on metal. So I checked everything and vacuumed everything. After I got the new part it took me about 5 minutes to put the new one on. And dryer works fine. Thanks for the quick response and I saved about $200.00!

replaced rear drum bearing

  • Customer: chuck from carroll NH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
the repair when ok the only problem I had was installing the small white plastic piece in the back without losing the ball bearing .and I also vac up everything inside as well lot of lint

My dryers was making a loud thumping sound. Like it was off balance.

  • Customer: Dennis from Maple Shade NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I Took the front off and saw the cushion was gone around the drum and glids were worn down. I ordered both parts . It took 5 minutes to glue the cushion back on around the drum and 2 minutes to snap the drum glids on.But what I couldnt believe was the amount of lint that was all over the inside of the dryer.I would suggest to anyone to take the dryer front off once a year and clean it all out . I now understand fully why there are dryer fires.But the fix was cake and it runs like new.

loud noise at back of dryer

  • Customer: sam from prattville AL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,

Squeaky noise from rear of dryer

  • Customer: Kenneth from Pensacola FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug dryer, remove rear access cover and removed belt from pulley. Remove bottom cover on front of dryer, remove top of dryer, unplug harness to control panel and remove front door assembly. Remove screws from drum to bearing assembly. Removed drum and belt removed bearing assembly by lifting up and out of the bearing socket. Vacuumed all the lint. Removed the bearing socket, installed all parts and covers in reverse order.

There were several pieces broken around the band and as the drum turned, clothes would catch the cuts and slice right though like a razor blade

  • Customer: David from Alto TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Take the top off the dryer. Once it's off, start inserting the bands from the inside. From the top or inside, control and move the drum as needed to insert band in place. Once band is in place, and holes line up, press down till you hear it snap in place. Repeat process with second band.

Banging coming from the dryer with light loads or when clothes we close to being dried

  • Customer: Bryan from Rome NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Use flat blade to compress clips so top could be raised. Use Philips to remove 2 screws holding front on. Popped front off and then removed old worn and broken glides. Had to lift the drum slightly when placing the front back on. Screwed in the 2 screws to hold the front on. Lowered and locked top. Be careful not to pinch any wires..
All Instructions for the SGR351CQ0
271-282 of 282