Models > SGR341AS0 > Instructions

SGR341AS0 Westinghouse Dryer - Instructions

All installation instructions for SGR341AS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SGR341AS0
1-15 of 391
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Squealing noise

  • Customer: Cynthia from Lexington SC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Wrench set, Wrench(Adjustable)
  • 383 of 386 people found this instruction helpful
We followed the instructions for the drum glide replacement and changed the belt and drum support bearing piece, cleaned it out too. Works like a charm. Thanks for saving us a bundle.

Loud Squeaking

  • Customer: Frank from Boyertown PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 244 of 252 people found this instruction helpful
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.

Drum glide wore down and caused close to get stuck between drum and front panel.

  • Customer: William from Boise ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 162 of 227 people found this instruction helpful
Unpluged dryer. Removed the top of dryer by pushing in a retaining clip on both sides of the front lip with a screw driver. Remove the two screws on both sides of front panel. These screws are square head or phillips #2. Unplugged the wiring harness to front panel (make sure power has been disconnected). Support drum and lean front panel away from dryer body. Front panel will pull off of tabs at bottom. The old drum glide is fiberous and hard to remove. I removed most of it with the pliers, but had to carefully scrape the balance of the glide off with the wood chisel. The adhesive that comes with the repair part has an acetone base, so I used acetone (or you could use nail polish remover) to remove the old adhesive. Once the acetone has dried, I applied an 1/8" snaking bead of adhesive to the front panel. There is more adhesive in the tube than you need so do not use too much. Make sure that you get adhesive as close to the base of the lower seal as you can. Follow directions on adhesive tube and then attach the glide. I let it set up for about 30 seconds. Place the front panel back on the tabs of the dryer. Carefully lift the drum an fit it on the front panel and insert the two screws holding the panel to the base. Reconnect the wiring harness and make sure it is not in contact with the drum. Check to make sure that all of the electrical connectors on the timer are still in place. Reassemble the dryer. Reconnect power.

Motor would hum but not turn on when start knob was turned.

  • Customer: Elvis from Miami FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 134 of 154 people found this instruction helpful
The motor bearings had stiffened up – classic planned obsolescence.

I could tell the motor was bad, because when I tried to spin the drum by hand, it wouldn't turn in any direction. (Normally it can turn fairly easily.)

(Helpful hint: As you remove screws / parts, place them in a plastic baggie, and write on the baggie from whence they came. This is especially helpful if you have to order parts and then wait a few days for them to arrive.)

You can replace the starter motor without removing the drum, but it is easier if you do remove the drum. Plus, I decided to also replace the drum belt, since it was 9 years old and is a wear part.

UNPLUG THE DRYER BEFORE YOU BEGIN.

1. Pop off the top cover; it has two spring clips at the front, then it hinges up. Disconnect the green grounding wire at the back, then slip the cover off the hinges and set it aside.

2. Remove the front panel:

a. Looking down into the dryer, disconnect the electrical harnesses that go between the front controls and the body. You may have to cut a nylon cable tie to access one or more. (Note that they have shapes that won't allow you to mix them up later). Also, there are two wires that attach to connectors in the top middle of the dryer, which are difficult to get at; you may need a needle nose pliers to pull them. Remember their color-coding for reinstallation.

b. Remove the two phillips screws located about 8 inches from the top, on either side, inside the body, that hold the front panel in place.

c. The front panel is now held in place by spring clips. Pry it gently to pop it loose. It will hinge out, then you can pull it up. Notice how the front piece has felt pads that serve to hold the front of the drum; you'll line it up the same way when it goes back together. Set the front panel aside.

3. Remove the rear motor vent plate.
a. It is at the back, lower right of the dryer (which is lower left once you're behind it). 2 phillips screws hold it in place.

b. Now look inside to see the motor and belt. Memorize how the belt feeds around the motor pulley and the larger, white plastic tensioner pulley. Notice how the rear motor bearing sits in a half-round metal plate, held down by a spring clip. (Make a drawing if you like.)

c. Move the spring- loaded tensioner arm to take tension off the belt, then slip the belt off the motor pulley.

d. Notice that the tensioner pulley, arm and spring are all held in place by the spring. Note that the tensioner pulley can slip off its shaft. Note these things for when you put it all back together later.

e. Now undo the tensioner arm spring and remove the arm, pulley and spring. Set them aside.


4. Remove the drum:

a. There is a yellowish plastic block at the top front of the open dryer body that holds the drum. Take it out with a phillips screwdriver.

b. Slip the now un-tensioned belt off the drum, to the back, so it hangs over the heater element body. You can leave it there for now, so you don't forget to install it before you put everything back together. If you're going to replace the belt, now is a good time to do so. (Check the length of the new belt against the old one, to make sure they're the same.)

c. Now you can remove the drum. It uses a center ball in a socket joint at the back to hold it in place. Use a screwdriver to lever upward on the back of the drum. This will pop the ball up, and then you can pull the drum out from the front.

5. Clean it up.
Now is a very good time to vacuum out any lint in the fan area, inside the dryer body, etc. Also consider removing the lint trap assembly from the dryer front ( 2 phillips screws) and vacuuming it out as well.

6. Remove the motor.

a. First, remove the fan that's attached to the front of the motor. Use a socket (7/8", I think) to unscrew the fan from the front of the motor shaft. IMPORTANT: The fan has a plastic hex nut sh

clothes got caught , burned and ripped on front of drum

  • Customer: john from owego NY
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 119 of 188 people found this instruction helpful
I felt ,if I was going to replace the top drum glide and lower basket seal, I might as well replace the belt ,bearing assembly and the idle pulley assembly and avoid having to replace these sooner than later. All of the parts showed alot of wear and the belt like all drive belts, should be changed every 5-6 years.
DISCONNECT ELECTRICITY and GAS LINES
1.popped top by pushing and prying at front /top clips about 2-3in. in from side edges. lifted it off
2. removed the front panel by removing the 2 top front screws from the inside, then the two lower screws from the front after removing the small white plastic hole covers. disconnected the multiplug electric connector top right. set panel aside.
3.remove small back panel.and loosened belt.(observe belt path and idle pulley assy.
4. lifted drum and slid it out the front.
5. using socket, removed rear plastic bearing housing and replaced the same. be careful of observing the small ball bearing and the small piece on outside back panel. replace the same. you wil probably need a second set of hands to hold the piece on the outside when screwing in the screws from the inside.
6. unscew the "bearing" from the rear of the drum and replace with new one.(the screws are self-tapping and go in HARD!!)
7. apply lubricant liberally to plastic bearing holder
8. place new belt around drum(rubber side against drum cloth side out.
9. idle pulley assy. is removed by removing spring and just sliding assy out of holder. replace with new
10. replace drum and belt
11. take front panel and remove top drum glide and lower basket seal.( i marked where the two seal/glide come together with a marker )
12. scrape and remove as much felt and possible. I then used "goo gone" to remove all the glue. clean well and using the provided high temp adhesive reattached glide and seal.
13. reassemble and enjoy your NEW? dryer

Dryer would heat initially then cool down

  • Customer: Brett from Monticello MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 43 of 47 people found this instruction helpful
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils were easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle.

Dryer was leaving marks on the clothes and they were getting stuck in the rim around the door .

  • Customer: LeAnne from Anaheim CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 26 of 29 people found this instruction helpful
Let me start by saying that I am a stay-at-home mommy of 2-year-old twin girls so if I can do this, you can too.
1. I disconntected the dryer from the outlet.
2. Then I had to pop open the top of the dryer. I had to wedge a screwdriver underneath the top lid (towards the front corners) in order to open the top.
3. Looking into the dryer from the top I could see a few screws I needed to remove that were along the sides of the drum. After removing the screws, I was able to remove the front panel of the dryer exposing the drum.
4. The seal that I needed to repair was located on the front panel. I had to remove the old seal (I had to scrap to get some of it removed).
5. I applied the adhesive then attached the upper and lower seals.
6. I let the seals dry for a few minutes then replaced the ront panel. In replacing the panel, the seals need to fit around the drum. You need to be careful in fitting the drum so that the seals remain intact and not pushed out of place.
7. Then, I simply replaced the screws to the front panel and secured the top lid back in place.
FYI: I did have a problem with the lower seal, in placing the drum over the seals, the lower was pushed out of place without me knowing. A few days later, the dryer was making a noise and clothes were still getting caught. After opening the dryer and examining the seal, I needed to reattach the seal. I was out of the adhesive but was able to use Gorilla glue (can withstand any temperature once it is dry). Works good as new now.
FYI: I also have to add that the actual replacing of the seals did not actually take 2 hours but since the dryer was opened, I took advantage and thoroughly cleaned the inside of the dryer.

Dryer would heat only on the initial start. Burner would not light again until completely cooled down. The ignitor would energize, but no gas would flow for ignition.

  • Customer: Bruce from Burnsville MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 26 of 29 people found this instruction helpful
1. Pry Dryer top up and off the clips. (Front of Dryer)
2. Remove 2 phillips screws on the inside of front panel.
3. Lift front panel up and set off to the side
4. Removed 2 phillips screws with short handled phillips driver that hold the gas valve coil bracket in place.
5. Unplugged and removed both coils, installed new coils and bracket. Re installed front panel, screws and top.

press start button, machine would just hum

  • Customer: Robert from Mt. Horeb WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 19 of 21 people found this instruction helpful
took off back vent panel, removed belt from idler pulley. tried motor again to see if it would work under no load. motor was not seized just would not run. concluded it was the motor. I removed the 2 mounting screws from the back of motor area. from there removed top of dryer and bolts for the front door panel. propped open the door panel to get to the fan housing and 2 front motor mount screws. disconnect the fan wires. pull out fan and motor assembly from front of dryer. I used a medium sized locking wrench behind the pulley and then mounted the wrench (attached behind the pulley in a vise) from there I was able to use a socket to take off the plastic nut at the end of the fan. Notice that it is a reverse thread so don't strip it. dismount motor from bracket and reasmble with new motor. all the steps in reverse. Since the motor was out it just made sense to replaced the belt at this time. took about 45 minutes to disassemble and just over an hour to get it all back together. Make sure you clean out the lint box from inside the dryer.. over the years it will accumulate a lot of nasty dust bunnies. check that all the surfaces are clear of dust and the back of the vent pipe to..

Dryer drum would squeak and squeal until warmed up, but progressively got worse as the days drug on.

  • Customer: Chad from Glyndon MN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 17 of 18 people found this instruction helpful
First pry up on the front edge of the top panel of the dryer which is held in place by snap in clips. Pivot the top open and support against wall or other taking care not to pull on wiring harness. Next remove the 2 screws that hold the front panel in place. These are located on the inside of the front panel. The front then snaps loose also. Remove the plastic drum stop located at the top edge of the front of the dryer. Next I removed the 3 drum screws located inside at the back center of the dryer. Next you can you need to remove the belt the motor located at the rear vent panel on the back. Slide the now loose drum out exposing the rear bearing. With a 5/16 end wrench, loosen the 2 screws on either side of the bearing retainer. Assemble the new bearing bracket to match the old one. Apply a liberal amount of supplied lubricant to the pivot ball and plastic retainer. At this point it was helpful to have someone at the rear of the dryer hold the new retainer bracket against the back of the dryer while I tightened the new bearing assembly in. Assemble dryer in reverse.

Dryer squealed loudly

  • Customer: Glenn from Fort Worth TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 18 of 22 people found this instruction helpful
First, I removed the top panel which is held on at the front by pressure clips. Second, I removed the entire front panel which entailed removing 2 screws and 2 wire couplings. Third, I removed the 3 screws on the inside center of the drum which turned out to be unnecessary. Fourth, I slid the drum forward in order to access the rear bearing. Lastly, I replaced the entire bearing assembly including the shaft, bracket, bearing, grounding ball and clip. Again, probably not needed but I had ordered the parts in advance in preparation for the worst.

Had 2-seperate problems; 1st was a high pitch squeel, 2nd was the cover overheating

  • Customer: Gerald from Cumming GA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 23 of 37 people found this instruction helpful
The high pitch squeel was the result of a failing drum bearing. It was particularly evident when first turning on the dryer, but became softer as the dryer heated up. In order to replace the drum bearing, I removed the top panel and front door panel.

The top panel was easily taken off by removing 2-screws from the back edge of the panel, and sliding it back to release it from the front panel seam.

The front panel is more involved, but still relatively easy for your average "do-it-yourselfer". I removed the front door panel by first removing the control panel (4-screws; 2 on top and 2 from the back of the panel). I removed 2 cable assemblies from the control panel via connecters (different sizes so didn't need to mark) and 2-wires attached to the large control panel mode selector (I marked these 2-wires). I set aside the control panel. I removed the front door panel by taking off 6-screws (2 on top, 2 on the bottom, and the remaining 2 on the inside of the panel on either side of the drum). After removing these 6-screws, I carefully pulled the front door panel away from the front of the dryer, carefully releasing 4-alignment latches (2 on either side). The front door panel was still electrically attached to the machine so I had to disconnect a couple more wires. I carefully disconnected 2-wires from the door light assembly and 3 more wires from the door switch (I marked the 3-wires on the door switch). I set aside the front door panel.

From the back of the dryer, I removed the small motor access panel on the bottom left corner. This panel also provides access to the drum belt. I released the drum belt from the motor drive wheel by releasing spring tension at the tensioner. The belt can easily be disconnected from the motor drive wheel and tensioner assemblies.

Removal of the drum was now possible. With the front door panel removed, the front of the drum is maintained in place via a small plastic stop on the top crossmember. I removed this stop prior to removing the drum. With one hand, carefully grabbing the belt that is was loosely draped across the back of the drum, and the other hand holding the front lip of the drum, I provided a quick and forceful upward motion to the back of the drum in order to dislodge the drum shaft from the bearing housing assembly. Once this was accomplished, I simple pulled the drum out of the dryer housing via the front of the machine.

The drum bearing repair kit ordered came with the replacement ball bearing, bearing housing, drum shaft, high-temperature grease, and attaching hardware.

I replaced the drum shaft on the drum via the 4-screws accessed on the drum rear panel.

I removed the old bearing/bearing housing via the 2-screws holding it in place. I wasn't too concerned about loosing the small ball bearing as the kit provided me a new one. I generously applied some high-temperature grease to coat the interior lining of the new bearing housing. I also placed a dab on the back seat where the new ball bearing sits. This helped hold the bearing in place while reattaching it. I reinstalled the bearing housing to finish replacing the repair parts.

Reassembly of the drum is in the reverse order. I paid particular attention to making sure the new drum shaft properly seated with the new drum bearing housing.

After reinstalling the drum and while the front door panel was still off the dryer, it was easy to inspect the blower housing. I found the squirrel cage had broken loose from the molded nut that attaches it to the motor shaft. That would explain the heat problem; the heat was not being exhausted through the duct.

THE SQUIRREL CAGE IS REVERSE THREADED. I was unable to remove the nut from the motor shaft as the design encompasses a metal bushing molded into a plastic nut shaped form. The plastic would not hold up to the force I was applying trying to loosen the squirrel cage. So I ended up removing the entire motor and blower housing assembly from the base

Dryer was squealing and leaving brown marks on clothes.

  • Customer: William from Ardmore OK
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 16 of 17 people found this instruction helpful
Disconnected power and vent then pulled away from wall. You will need to move the dryer away from the wall to replace the ground bearing and retaining plate and/or the dryer belt. Removed top of dryer, disconnected wiring harness' then removed the two screws that hold the front panel on the dryer. After removing the two screws, lift out and then up on the front panel. This should remove it from the retaining clips on the bottom. To remove the dryer belt, remove access panel on rear/ bottom left of dryer. Just inside the panel you will see a tension pulley held by a spring. Use your hands to relieve the tension on the belt and remove the belt from the bottom pulleys. Now go to the side of the dryer and attempt to lift up on the front and back of the drum to remove it from the rear bearing guide. There is a slot that it rides in and it only needs to come up about an inch or so. If you cannot get the the rear bearing free this way, you will have to get inside the drum and remove the three screws in the back of the drum. There are two sets of screws, remove the inside circle of screws. At this point, the drum should slide out the front of the dryer. Use aSharpie to mark the center of the top guide on the metal then use a chisel or putty knife to remove the old guides from the front panel of the dryer. You probably won't be able to remove all of the old glue, but make sure you remove all of the old felt. Lay the panel front down and apply glue to the new top guide. Line up center of top guide with the mark you made earlier. Clamp in place. I used several spring clamps, but clothes pins will work. Now put glue on the bottom guide and clamp it in place. The bevel on the bottom guide will point to the back of the dryer. Now, while your dryer is disassembled and the glue is drying CLEAN IT OUT!!! You'll have no better opportunity to thoroughly clean this thing. Remove old bearing guide from the back of the dryer and replace with the new one. This will include the new grounding bearing and retaining plate. Apply high temp grease (generously) to the new bearing guide. Remove old rear drum bearing from drum and install new one. Take old belt off drum and put new one on. Place drum back in dryer cabinet. Be sure new belt doesn't snag or hang on anything. Guide the new rear drum bearing into the groove on the top of the guide and push down into place. It should be a snap ;-). GO to back of dryer and reinstall new dryer belt around pulleys. I put a little of the high temp grease on the guide pulley shaft on the tensioner. Replace access panel. Reinstall front panel by placing bottom back into the two retaining clips and then use your free hand to lift up the drum and guide it into place around the new guides while pushing the top of the panel into place. Replace top screws in front panel and reconnect wiring harness'. Replace top of dryer, slide dryer into place and reattach vent. Hope thos helps someone. It really wasn't very hard.

Drying times continued to increase over several months until finally dryer wouldn't dry any more.

  • Customer: Francisco from Arvada CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 16 of 18 people found this instruction helpful
I did not troubleshoot my gas dryer to find the exact part that needed to be replaced. Instead, I did some research and found that the ignition coils are an extremely common problem.

The top panel of my gas dryer is attached by two snap clips located in the front, about three inches in from each side. I slid a butter knife in the space between the top panel and the front panel to push the clips and release the top panel. Front panel is attached by two screws, one on each side. I removed the front panel to access the heating system on the bottom left of my dryer and immediately saw the two ignition coils with a metal cover on top of them. Removing the metal cover was a little difficult because the two screws holding it in place were stuck. Once the metal cover is off, the two coils simply slide out. On my dryer, the bigger coil had a metal sleeve inside the core. I kept it and used it with my replacement parts.

The most difficult part of the repair was figuring out how to take appart the dryer to access the heating system. Now, the ol' lady is bragging to her friends that I didn't just fix the dryer, but that i've actually made it better than when it was new ;-)

Not heat from the dryer

  • Customer: Hui from Chicago IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 16 of 18 people found this instruction helpful
First of all, let me thank your wonder web site and service.


Here is the step-by-step procedure:


Unplugged the power.

Accessed the heater assembly from the front left lower corner.

Turned off the small gas valve.

Unscrewed the copper nut connecting the small gas valve and the heater assembly.

Disconnected the 3 wire connectors.

Unscrewed 2 screws under the heater assembly.

Took out the heater assembly.

Unscrewed the screw for the igniter assembly.

Installed the new igniter assembly. Be very careful with the M shaped coil. I broke a new one. That is why I have order the same part twice. But it still cost me less for hiring a tech or buying a new dryer.

Carefully put the heater assembly back into it position.

Connected the gas connector.

Secured the heater assembly to the bottom of the dryer with 2 screws.

Connected 3 wire connectors.

Turned on the small gas valve.

Plugged in and ran a test.

It worked!!.
All Instructions for the SGR341AS0
1-15 of 391