SGR341AQ2 Westinghouse Dryer - Instructions

My order confirmation email had a "how to" video for installing the parts I ordered. I just watched the video, and the installation was ridiculously easy! We've put up with the obnoxious screeching noise for probably about two years, and with about $40 in parts and less than an hour of work time, we have practically a new dryer!!

took front panel off, removed access panel in rear to disconnect the belt from motor. removed top panel (this is a stack unit) take plastic rivets loose from lint trap, remove lint trap tube, pull drum out after slightly pulling up to dislodge drum from bearing cradle, Remove bracket and bearing from back of unit, clean parts of old grease (be carefull not to loose small ball bearing on back) Reassemble parts using moderate amount of new grease, put parts back together in reverse order.

This is a front load dryer. First unbolt top cover of dryer. Then unbolt screws and connections to control panel. Next unbolt all screws holding dryer door and front bottom panel. Next take belt off of drum and slide out drum from the front. From inside of drum remove 3 screws and remove bearing then put new bearing on and bolt up the same way you take old one off. Using an 8mm socket or wrench remove plastic bearing cage located at rear of dryer. When unbolting there is a retaining clip and small steel ball to be removed from back of dryer. Replace this the same way you take it off. He sure to grease the bearing cage then replace everything back from putting the drum in first to your last step bolting on top cover of dryer. Hope this helps anyone doing this repair.

I have used this company twice now and both times have been a good experience. Would highly recommend!

Many thanks for the video you guys put together on replacing dryer belts! I didn't know how I was going to get inside the dryer. I had the dryer apart in 10 minutes! Had to wait a day for the belts to come in. New belt in and dryer running in 15 minutes! Thanks for running a first class operation!! Jim

I heard the dryer running, but I didn't hear it tumbling like usual, so I got suspicious. I popped the top off of the dryer to reveal a broken belt. Installation took 20 minutes.

Could not figure out how to get into the dryer. Wasted a couple hours trying different things. Found a video online which showed the repair I wanted to make. After that it was easy. One needs to be tall and in shape to lift the drum out of the case....or have the help of a second person. Only a little blood was shed but now feel confident I can replace any of the parts in the dryer if needed.

Everything I needed to know was already on your website. Prying off the top of the dryer (with a big screwdriver under the front of the top) was the hardest thing, since I was afraid I would break something. Only then can the front be removed (taking out just 2 phillips screws). The rest is easy.

put door catch in hole

Followed your very helpful video instructions. Saved me a ton. Five stars!

pushed screwdriver into the two clips between the top and front to release the connection. took off front. at the bottom front left side, took out screws to access parts that needed to be replaced. put everything back together. dryer works like new. easy.

I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.

i followed the video step by step & i never thought a repair could go so well thanks to the repair video

Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.

After figuring out how to remove the top, front, and control panel from the Gallery series, which is different than the dryer in the video, the repair was easy. Just followed the rest of the proceedure in the video.